Answered: A bolt has requirement of being…

A bolt has requirement of being tightened to 38Nm. You pull on the end of a 25cm wrench at an angle of 120 degrees to the radial arm line. What is the forst of the full needed?

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 20P: A boy rides his bicycle 2.00 km. The wheels have radius 30.0 cm. What is the total angle the tires...

See similar textbooks

Related questions

Q: If the torque required to loosen a nut on the wheel of a car has a magnitude of 40.0 Nm, what…

A: Given data: Torque (τ) = 40 Nm Perpendicular distance (r) = 50 cm = 0.5 m Required Force (F) =?

Q: When a wrench is rotated the magnitude of the torque is 26N.m A 95-Force is applied 35 Cm from the…

A: The free-body diagram of the wrench is shown below. Here, F is the applied force and θ is the…

Q: rt B culate only the force that exert the torque menti Submit Request Answer

A: Apply formula of magnetic force on conductor

Q: The dimensions and confi ws: P,A 300 mm; P,B 2= 60°. The crank P,Aha ngular velocities and angu…

Q: If a baseball player pushes with 250N due North at a point 8.0cm due southeast of the pivot point of…

Q: Given the figure below, the weight of the bar is 5 lb and its total length is 9 ft. The moment in…

Q: What is the total net torque on the rod? 25ON 65N 45

A: We need to tell the total torque on the rod about the hinge.

Q: A bolt requires tightening to a torque of 94 N-m. If a wrench is 28 cm long, what perpendicular…

A: The product of the force to the perpendicular distance from the end of the boat is known as torque.

Q: If the force is applied r = 0.20 m from the axis of rotation, what magnitude of torque is produced?

A: Torque = R.F or =(RsinΦ )F where RsinΦ = perpendicular distance between axis of rotation and force.…

Q: If the torque required to loosen a nut on the wheel of a car has a magnitude of 40.0 N•m,what…

A: Minimum force(F) required to exert by a mechanic. given,magnitude of torque(τ)=40 Nmperpendicular…

Q: I push down on a wrench with 35lbs of force, 8 inches from the but I'm trying to break free. How…

A: Given,Force, F= 35 lbs, and length, l= 8 in=0.67 ft.

Q: subjected to the force F = 24.3(t + 1) Ib where t is in seconds. If the cabinet is

A: Given Force= 24.3(t+1) Velocity = 19 ft/s mass=190.3 lb

Q: 12 1b

A: Given: The length of the rod is 9 ft. The weight of the rope is 5 lb.

Q: A torque of 50 Nm is required to loosen a particular bolt. What force is needed for a 0.5 meter…

Q: A person exerts a horizontal force of 46N on the end of a door 97cm wide. What is the magnitude of…

Q: For the given figure, the weight of the 9-ft bar is 5 lb. The moment of the tension in the cord…

Q: If the force is applied r = 0.16 m from the axis of rotation, what magnitude of torque is produced?

A: Torque is defined as a measure of the force that can cause an object to rotate about an axis. The…

Q: Given, Tr = Tlr = Tlsin(0), at what angle 0 will torque be maximized?

A: As we know.. torque = r×F torque = rFSin(theta) ;

Q: A box is placed on the right hand side of a see saw, producing a-389 Nm torque (clockwise). If a…

Q: Men are opening a 1,250-kg, 1.75m-wide door (with well-lubricated hinges) by applying to its edge a…

Q: The bolts on a car wheel require tigthening to a torque of 90 N x m. If a 30 cm long wrench is used,…

Q: A wheel, 3 fect in di ameter, Pt. f contact of the wheel with the inaline s ¢ ft. fnom the base oF…

A: Given Data : The diameter of the wheel is given as d = 3ft. The angle of inclination of the plane…

Q: net Torque? what disection is the wheel moring? what Is 4ON 60 N

A: Torque = Force x r where r= radius of wheel= 0.5m

Q: Ayoung man was jumping on a diving board with a length of 2.44 meters. If the force ne exerted on…

Q: If you increase twice the force and decrease the arm 4 times in respect to the initial, what is the…

A: The initial torque of the object is, τi=Fr The final torque of the object is, τf=2Fr4

Q: cylinder consisting of an outer radius ha force F1 = 3N. A second string is 5m, what is the net…

A: The correct option is (d).

Q: A rope te wound around a shaft 10cm in diameter. If a pull of 500N is exerted on the rope, what…

A: Torque imparted to the shaft = Force × perpendicular distance from the axis about which the rod will…

Q: An old streetcar rounds a flat corner of radius 6.90 m, at 12.0 km/h. What angle with the vertical…

Q: A man opens a 1.00-m wide door by pushing on it with a forceof 50.0 N directed perpendicular to its…

Q: The linear displacement of the knee joint about the hip center of rotation is 1.11m and the angle of…

Q: A platform rotates freely at 100 rev/m. If the co- efficient of static friction is 0.5, how far from…

A: Explanation As the platform rotates freely there is centripetal force acting on the bolt. If the…

Q: A flywheel is rotating at 36.5 rev/s. What is the total angle, in radians, through which a point on…

A: Answer:- Given Angular velocity (w) = 36.5 rev /s (Omega = w) w = (36.5 × 2π ) rad/s w =…

Q: A worker applies a torque to a nut with a wrench 0.500 mlong. Because of the cramped space, she must…

Q: An old streetcar rounds a flat corner of radius 9.70 m, at 13.0 km/h. What angle with the vertical…

A: The old streetcar rounds a flat corner of radius: Speed of the old streetcar(v) is

Q: Two men exert forces of P = 50lb and F 80 lb on the ropes. Determine the %3D moment of each force…

A: Given data: The magnitude of force P = 50lb. The magnitude of force F = 80lb.

Q: Determine the resultant force on the bolt in

Q: A strut of lengthL = 3.00 m and mass m =16.0 kg is held by a cableat an angle of θ = 30.0°with…

A: Part A:

Q: For the given figure, the weight of the 12-ft bar is 5 lb. The moment of the tension in the cord…

Q: The weight of the 9-ft bar is 5 Ib. What is the moment of the tension in the cord about the fulcrum…

A: Given: The length of the rod is 9 ft. The weight of the bar is 5 lb.

Q: A rusted bolt requires 30J of torque to be loosened. If only 40N of force is applied to a wrench…

Q: find the total force experienced by the figure spire and the net torque on the spire pls dont skip…

A: Magnetic force on a wire is given by F→=idl→×B→the direction of is along the direction of current.…

Q: ) If the torque required to loosen a nut that is holding a flat tire in place on a car has a…

Q: To loosen the lid on a jar of jam 7.6 cm in diameter, a torque of11 N # m must be applied to the…

A: The applied torque to the circumference of the lid, The extends of the wrench from the center of…

Q: The lug nuts on a car wheel require tightening to a torque of 90 N.m. If a 30 cm long wrench is…

A: Required Torque= 90 N.m Length of wrench= 0.3 m

Q: If the torque required to loosen a nut on the wheel of a car has a magnitude of 41.8 N*m, what…

Q: A force of 200 N is applied to a wrench at 80° to the handle, 10 cm from the centre of the bolt.…

A: Given: Force: Angle: Distance:

Q: A wheel 25 cm in radius turning at 120 rpm increases its frequency to 660 in 8 s . Find the constant…

A: Given: The radius of the wheel is 25 cm. The initial angular velocity of the wheel is 120 rpm. The…

Concept explainers

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.

Question

A bolt has requirement of being tightened to 38Nm. You pull on the end of a 25cm wrench at an angle of 120 degrees to the radial arm line. What is the forst of the full needed?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

• Pulling the string on a bow back with a force of 28.7 lb, an archerprepares to shoot an arrow. If the archer pulls in the center of thestring, and the angle between the two halves is 138°, what is thetension in the string?
A bolt has a requirement of being tightened to 38Nm. You pull on the end of a 25cm wrench at an angle of 120 degrees.To the radial arm line. What is force of the pull needed?
When tightening a bolt, you push perpendicularly on a wrench with a force of 165N at a distance of 0.140m from the center of the bolt. How much torque are you exerting relative to the center of the bolt?
If we assume that the tip of the mandible hits perpendicular to ground, what is the force on the tip?
The wheel has radius ?? = 60 cmand is free to rotate without friction about acentral axle. A force ?? = 15N is applied tothe wheel as shown, at distance ?? = 20 cm.from the axle. ?? = 50°
The bolts on a car wheel require tigthening to a torque of 90 N x m. If a 30 cm long wrench is used, what's the magnitude of the force required when the force applied at 53 degrees to the wrench?
A worker applies a torque to a nut with a wrench 0.500 mlong. Because of the cramped space, she must exert a forceupward at an angle of 60.0° with respect to a line from thenut through the end of the wrench. If the force she exerts hasmagnitude 80.0 N, what magnitude torque does she apply tothe nut?
Pulling the string on a bow back with a force of 24.0 lb , an archer prepares to shoot an arrow. If the archer pulls in the center of the string, and the angle between the two halves is 126 ∘ , what is the tension in the string?
For the given figure, the weight of the 12-ft bar is 5 lb. The moment of the tension in the cord about the fulcrum (point O) is:
find the magnitude of the torque exerted by F on the bolt at P if |PQ| = 8 in. and |F| = 30 lb. Answer in foot pounds.
When a wrench is rotated the magnitude of the torque is 26N.m A 95-Force is applied 35 Cm from the fulcrum. At what angle to the wrench is the force applied?
Wouldn't the torque equal Fx +Fy?