A brass washer has an outside diameter of 4.50 cmcm with a hole of diameter 1.25 cmcm and is 1.50 mmmm thick. The density of brass is 8602 kg/m3kg/m3. If you put this washer on a laboratory balance, what will it "weigh" in grams? (Recall that density is mass divided by volume.) Express your answer in grams.

A brass washer has an outside diameter of 4.50 cmcm with a hole of diameter 1.25 cmcm and is 1.50 mmmm thick. The density of brass is 8602 kg/m3kg/m3. If you put this washer on a laboratory balance, what will it "weigh" in grams? (Recall that density is mass divided by volume.) Express your answer in grams.

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter15: Fluid Mechanics

Section: Chapter Questions

Problem 37P: A horizontal pipe 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the...

See similar textbooks

Similar questions

The inside diameters of the larger portions of the horizontal pipe depicted in Figure P9.45 are 2.50 era. Water flows to the right at a rate of 1.80 104 m3/s. Determine the inside diameter of the constriction. Figure P9.45
The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN? Figure P15.6
The inside diameters of the larger portions of the horizontal pipe depicted in Figure P9.45 are 2.50 era. Water flows to the right at a rate of 1.80 104 m3/s. Determine the inside diameter of the constriction. Figure P9.45
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate the new flow rate for the following changes with all other factors remaining the same as in the original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid with 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube is used with a radius 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half the length, and the pressure difference is increased by a factor of 1.50.
Figure P15.47 shows a stream of water in steady flow from a kitchen faucet. At the faucet, the diameter of the stream is 0.960 cm. The stream fills a 125-cm3 container in 16.3 s. Find the diameter of the stream 13.0 cm below the opening of the faucet. Figure P15.47
A glucose solution being administered with an IV has a flow rate of 4.00 cm3/min. What will the new flow rate be if the glucose is replaced by whole blood having the same density but a viscosity 2.50 times that of glucose? All other factors remain constant.
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
What fraction of an iceberg floating in the ocean is above sea level? Assume the density of the iceberg is 917 kg/m3.
A rod extending between x = 0 and x = 14.0 cm has uniform cross-sectional area A = 9.00 cm2. Its density increases steadily between its ends from 2.70 g/cm3 to 19.3 g/cm3. (a) Identify the constants B and C required in the expression = B + Cx to describe the variable density. (b) The mass of the rod is given by m=allmaterialdV=allxAdx=014.0cm(B+Cx)(9.00cm2)dx Carry out the integration to find the mass of the rod.
Mercury is poured into a U-tube as shown in Figure P15.17a. The left arm of the tube has cross-sectional area A1 of 10.0 cm2, and the right arm has a cross-sectional area A2 of 5.00 cm2. One hundred grams of water are then poured into the right arm as shown in Figure P15.17b. (a) Determine the length of the water column in the right arm of the U-tube. (b) Given that the density of mercury is 13.6 g/cm3, what distance h does the mercury rise in the left arm?
Figure P15.52 shows a Venturi meter, which may be used to measure the speed of a fluid. It consists of a Venturi tube through which the fluid moves and a manometer used to measure the pressure difference between regions 1 and 2. The fluid of density tube moves from left to right in the Venturi tube. Its speed in region 1 is v1, and its speed in region 2 is v2. The necks cross-sectional area is A2, and the cross-sectional area of the rest of the tube is A1. The manometer contains a fluid of density mano. a. Do you expect the fluid to be higher on the left side or the right side of the manometer? b. The speed v2 of the fluid in the neck comes from measuring the difference between the heights (yR yL) of the fluid on the two sides of manometer. Derive an expression for v2 in terms of (yR yL), A1, A2, tube, and mano. FIGURE P15.52