A building with a rectangular footing is constructed as the following figure. The design building load to the footing is 12800 kN. The unit weight of soil and consolidation test parameters of the Clay layer are provided. Calculate the clay consolidation settlement along the center of footing due to the loading. The initial void ratio, eo, is 1.15. Use DM 7.01 manual to find the influence factor and one sublayer approach for the clay formation.

A building with a rectangular footing is constructed as the following figure. The design building load to the footing is 12800 kN. The unit weight of soil and consolidation test parameters of the Clay layer are provided. Calculate the clay consolidation settlement along the center of footing due to the loading. The initial void ratio, eo, is 1.15. Use DM 7.01 manual to find the influence factor and one sublayer approach for the clay formation.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Mat Foundations

Section: Chapter Questions

Problem 10.1P: Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The...

See similar textbooks

Similar questions

A square footing of dimension 1.5m x 1.5m carries a load of 890 kN as shown in the image: Determine the following: (d) primary settlement for normally consolidated clay using exact equation for additional pressure at midpoint of clay. (e) primary settlement for normally consolidated clay using approximate equation for additional pressure at midpoint of clay.
Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The distance between the two column loads L3 = 13.5 ft. The proximity of the property line at the left edge requires that L2 = 3.0 ft. The net allowable soil pressure is 2500 lb/ft2. Determine the breadth and length of a rectangular combined footing.
A 3 m 4 m footing, founded at 2 m depth in a clay, applies a net pressure of 200 kN/m2. The bed rock lies 10 m below the footing. The modulus of elasticity of the clay is 30 MN/m2. Using Janbus generalized relationship [Eq. (17.1)], assuming undrained conditions and flexible footing carrying uniform pressure, estimate the expected settlement.
A 2.0 m 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c = 0, = 26, = 19 kN/m3, and cu = 60 kN/m2. Determine the maximum possible value for Q, considering short-term and long-term stability of the footing.
A soil formation is composed of 5m thick clay and 5m thick sand being sand above the clay. The groundwater table is located at 2m below the ground surface, assume E=6900kPa, If=0.79 and µ=0.2 a. A rigid column footing 1.2m in diameter is constructed. The load on the footings is 170kN. Determine the immediate settlement in mm. b. Calculate the primary compression index. c. Calculate the primary consolidation settlement of the normally consolidated clay layer if there is a surcharge of 40kpa acting on the ground surface. (neglect footings load) in mm.
A rigid footing with B = 3m and L = 4m carries a total load of P = 890kN as shown. A.) Determine the elastic settlement of the footing if the Poisson’s ratio (µs) of soil = 0,32, modulus of elasticity of soil Es = 15900kPa, Influence factor Ip = 0.88. B.) Compute the primary consolidation settlement of clay layer if it is normally consolidated. C.) Compute the total consolidation of the clay 6 years after the completion of primary consolidation settlement. Time for completion of primary settlement is 2 years.
A square footing 3 m x 3 m is supporting an axial load of 650 kN. The weight of the soil is aasumed to be 17.32 kN/m^3. Compute the vertical stress increment due to this load at a depth of 1.5 m below the center of the footing using the approximate method. a. 51.46 kPa b. 32.10 kPa c. 76.54 kPa d. 50.56 kPa
A spread footing with a dimension of 2.0 m x 2.0 m is embedded in uniform clay at a depth of 1.0 m to support a vertical downward load of 300 kN. The pre-consolidation stress of the soil is 50 kPa and their compression indices are Cr/(1+e0) and Cc/(1+e0) of 0.025 and 0.11, respectively. The soil has unit weights of 16.8 and 17.8 kN/m3 above and below the groundwater table, respectively. The soil stratum extends to a great depth and the ground water table is at a depth of 1.5 m below the ground surface. Estimate the consolidation settlement of this footing. Use 2:1 method to estimate induced stress due to the applied load. The depth for settlement calculation is assumed to be 5 m below the foundation and use layer thickness of 1 m.
A footing 2m square is located a depth of 4m in a stiff clay of saturated unit weight 21kN/m3. The undrained strenght of the clay at a depth of 4m is given by the 3 parameters c=120kN/m2 and φ=0o . For a factor of a safety of 3 with respect to shear failure ,What load could be carried by the footing.
A long strip footing 3.5 ft wide is to be used to support a masonry bearing wall for a building. The subsurface investigation indicates that the soil at the site is a clay with a unit weight of 110 pcf and a cohesion, c, of 1,200 psf. The angle of internal friction is zero. The clay has a rigidity index of 10. The foundation is constructed 3 ft below the ground surface, and the soil backfill is well compacted. Using a factor of safety of 3, what maximum load should the foundation be designed to support per foot of wall length?
A 2.5m thick clay is to support a footing as shown below. Assume that the pressure increase Ao' is averaged at the middle of the clay layer. Determine the consolidation settlement using 1. Boussinesq equation 2. 1:2 Method
It is not marked questions. Plz, solve the two parts of this problem and try to solve it step by step, plz, solve the problem using my Reg.No : 5395. This is the Reg.No : 5395 Irrigation Engineering Q.1. Figure 1 can be seen a section of a hydraulic structure on permeable foundation. Calculate the average hydraulic gradient according to a) Bligh’s creep theory b) Lane’s weighted creep theory Also, find the uplift pressures at points A and B, and the floor thickness required at these points.