A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.

A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve ellaborately and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You. A pulley 190 mm. in diameter transmits 22 kW at 350 rpm. The arc of contact between the belt and pulley is 115.7° having a center distance of 410 mm. Determine (a) diameter of the driven pulley for open belt drive,(b) speed of the driven pulley, and (c) belt length for an open belt connection. (a) Diameter of Driven Pulley Answer and unit for part 1 (b) Speed of the Driven Pulley Answer and unit for part 2 (c) Belt Length
Design the rectangular key for a shaft of 50mm diameter. The shearing and crushing stresses for the key material are 42MPa and 70MPa. Determine the length in mm. From Table 13.1, we find that for a shaft of 50mm diameter, the Width of the key. w=16mm and thickness of the key, t=10mm
Consider a screw used in translation along with a 22 mm. inside diameter and 38 mm. outside diameter collar. The screw has a mean; diameter of 18 mm. and has a single trapezoidal metric thread cut with a pitch of 4 mm. Determine the torque required to raise a load of 500 kg, if both the collar and the threads have a coefficient of friction of 0.3.
Please solve ellaborately and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You! A pulley 600 mm. in diameter transmits 40 kW at 500 rpm. The arc of contact between thebelt and pulley is 144° having a center distance of 1100 mm. Determine: (a) diameter ofthe driven pulley for open belt drive, (b) speed of the driven pulley, and (c) belt length foropen belt connection.
The coefficient of friction of a disk clutch with two pairs of contact surfaces is 0.25. The maximum pressure under working conditions is 220kPa only. The clutch is used to connect two 25mm solid shafts with allowable shearing stress of 69 MPa. The inner and outer diameter of the clutch face is 60 mm and 120mm, respectively. What is the power in kW transmitted at 1000 rpm?
Torque in = 40nm Holding torque out = 896nm 8.Using your answers from the gear box above, and given that the input shaft has a diameter of 12 mm and the output shaft has a diameter of 15 mm, both shafts are made from aluminium. When this transmission system was operated, it failed. Identify the position where the failure occurred and the reason for this failure. Suggests improvements to the system to overcome the failure mode. The shear strength of aluminium is 207 MPa.
A roller chain is to transmit 5 hp from a gearmotor to a wood-working machine, with moderate shock. The 1-in output shaft of the gearmotor turns n = 500 rpm. The 1 ¼-in. driven shaft turns 250 rpm; C »16 in. (a) Determine the size of sprockets and pitch ofchain that may be used. If a catalog is available, be sure maximum bore of sprocket is enough to fit the shafts. (b) Compute the center distance and length of chain. (c) What method should be used to supply oil to the chain?
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
A motor is to transmit 150 kW to a piece of mechanical equipment. The power is transmitted through a solid structural steel shaft. Failure is by yielding, and the factor of safety is 1.25. The designer has the freedom to operate the motor at 60 rpm or 6000 rpm. For each case, determine the minimum shaft diameter. Shafts are available with diameters in increments of 5 mm. If weight is important, which speed would be used?
An engine cylinder has a compression ratio (r) of 7.5, a clearance volume of 35 cm3 and a piston stroke length of 325 mm. What is the bore diameter in millimetres (mm) for the engine cylinder to the nearest mm.
A belt is to transmit 50 kW power to a machine. The sheave is 10 inches in diameter and turns at 1200 rpm, while the larger sheave turns at 500 rpm. Determine the design HP if a service factor of 1.35 and a correction factor of 0.85.
A single stage spur gear gearbox has a module of 1.5mm and an input speed of 1500.p.m. and a pinion with 15 teeth. The overall ratio of the gearbox is 6:1 and the gearbox is transmitting a power of 6000W. If the factor of safetv is to be reduced to an absolute minimum acceptable value and the gears are to be made from a material with a Yield stress of 540 MPa, what is the face width of the gears (in mm) Express your answer in the form 21.00 ie with two decimal place an no units