1 B Find the state differential equations and the A, B, C, and D matrices foreach of the mechanical systems in Fig. P 2.8. The input is f(t) and theoutput is z1(t) for both systems.a)KllM R)Z2(1)z,(1)b)KllM– A()22(1)(1) 2

Answered: Image /qna-images/answer/be9aca85-695a-4ab5-981a-88bda434bf5d.jpg

Answered: А, C, and D matrices for each of the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

system modelling and analysıs
Consider a physical system with a three-dimensional state space. An orthonormal basis of the state space is chosen. In this basis the Hamiltonian is represented by the matrix H = [2 1 0 1 2 0 0 0 3] What are the possible results when the energy of the system is measured? A particle is in the state| psi > which is represented in this basis as, with i = Squareroot (-1), 1/Squareroot 3 [i -i i] Find , , and Delta H.
A certain ideal gas (unknown) inside a close piston-cylinder assembly undergoes a set of processesthat composed of Isothermal expansion from State point 1 to state point 2, Isometric heat rejectionfrom state point 2 to state point 3, and Isentropic compression from state point 3 back to the initialcondition. If the maximum pressure is 3000kPa and maximum and minimum volume is 200cm3and50cm3, analyze the problem and perform the following:a. Draw and label the graph of this set of processes in the P-V and T-S diagram showing the statepoint numbers and energy directions.b. From the known ideal gases as shown in Table 1.0, select the best suited ideal gas to attain theprocesses stated if the lowest pressure is limited to 629.8kPa. Assume a constant specific heat.c. For the selected ideal gas from b, compute the work of compression (kJ/kg), work of expansion(kJ/kg), and heat rejected (kJ/kg
A certain ideal gas (unknown) inside a close piston-cylinder assembly undergoes a set of processesthat composed of Isothermal expansion from State point 1 to state point 2, Isometric heat rejectionfrom state point 2 to state point 3, and Isentropic compression from state point 3 back to the initialcondition. If the maximum pressure is 3000kPa and maximum and minimum volume is 200cm3and50cm3, analyze the problem and perform the following: a. Draw and label the graph of this set of processes in the P-V and T-S diagram showing the statepoint numbers and energy directions. b. From the known ideal gases as shown in Table 1.0, select the best suited ideal gas to attain theprocesses stated if the lowest pressure is limited to 629.8kPa. Assume a constant specific heat. c. For the selected ideal gas from b, compute the work of compression (kJ/kg), work of expansion(kJ/kg), and heat rejected (kJ/kg)
Find the two-dimensional temperature distribution T(x,y) and midplane temperature T(B/2,W/2) under steady state condition. The density, conductivity and specific heat of the material are ρ =1200 kg/m 3, k=400 W/m.K, and cp=2500 J/kg.K, respectively. A uniform heat flux q =1000 W/m 2 is applied to the upper surface. The right and left surfaces are also kept at 0oC. Bottom surface is insulated.
Think of a window in a house as a system boundary separating the air on opposite sides of the glass pane. Draw the flow of thermal energy through the window when the indoor temperature is 23 °C and the outdoor temperature is 15 °C. Then show how the system model would change if the temperature outside were warmer than inside. How would bright sunshine affect the system?
This subject is Statics of Rigid Bodies. Show your solution step by step
Suppose a spring with spring constant k=1 supports a mass of 1kg and is subject to a driving force f(t)=sin2t. The mass is initially at rest at its equilibrium point. At time t=2, the mass is hit with a sharp upward blow, so that the force of the blow is δ(t−2). Set up and solve (using Laplace transforms) an initial-value problem modelling this situation.
Find: State-space representation Note: Output of mechanical system is X3(t) Given: M1=1 kg, M2=1 kg, M3=1 kg K1=1 N/m, K2=1 N/m Fv1=1 N-s/m, Fv2=1 N-s/m, Fv3=1 N-s/m, Fv4=1 N-s/m
Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20 oC, TL=8200 oC. The density, conductivity and specific heat of the material are ρ =800 kg/m3, k=200 W/m.K, and cp=2500 J/kg.K, respectively. Also, r1=820 cm and L=1640 cm.
2. Find the Diameter of a wind turbine rotor which generates 210 kW of electrical power output in a steady wind velocity of 8.5 m/sec with the power coefficient is 63%. The gear, generator and electric efficiencies are 95%, 96% and 89% respectively. Assume the atmospheric air condition is 1.01325 bar, Gas Constant R = 287 J/kg K at 29°C.
show your solution how you get the solutionsubject:Dynamics of Rigid bodies

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

А, C, and D matrices for each of the mechanical systems in Fig. P 2.8. The input is f (t) and the output is z1(1) for both systems. a)