A calibration curve was created to determine the quantity of protein in a solution. The calibration curve has the form of a straight line with the equation ?=0.0182?+0.007 where ? is the corrected absorbance of the solution and ? is quantity of protein in the solution in units of micrograms (μg). Determine the quantity of protein in a solution that has an absorbance of 0.305. A blank solution has an absorbance of 0.060. The answer (Quantity of protein) should be in units of (μg)

A calibration curve was created to determine the quantity of protein in a solution. The calibration curve has the form of a straight line with the equation ?=0.0182?+0.007 where ? is the corrected absorbance of the solution and ? is quantity of protein in the solution in units of micrograms (μg). Determine the quantity of protein in a solution that has an absorbance of 0.305. A blank solution has an absorbance of 0.060. The answer (Quantity of protein) should be in units of (μg)

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter20: Molecular Spectroscopy And Photochemistry

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An unknown concentration of [FeSal]+ gave an absorbance reading of 0.301. Calculate the concentration of the solution, given that the slope of the standard curve was 1280 and the y intercept was -0.00821.
A student creates a sports drink by dissolving 5.0 g of powder in 250 mL of water. The green colour of the drink is due to the presence Green Dye X, which has a lambdamax of 630 nm. A calibration curve (absorbance versus concentration) at lambdamax is created for varying concentrations (mM) of Green Dye X which has the equation y = 26.4x. If 1.0 mL of the sports drink is diluted to 10. mL with water, then the absorbance is measured to be 0.450, what is the mass percent of Green Dye X in the drink powder if the molecular weight is 418.4 g mol-1?
Given that the percent transmittance of light through a sample was 27.6% what is the absorbance of the solution? Rounded to two sig figs.
The equation of your standard curve of absorbance versus concentration (mM) is y = 1.245x + 0.0012. You put a solution of unknown concentration into the Spec20 and get an absorbance value of 0.227, which lies within the standards used to make the standard curve. What is the concentration of the unknown solution in mM?
"[FeSCN2+]eq is calculated using the formula: [FeSCN2+]eq = Aeq/Astd? [FeSCN2+]std where Aeq and Astd are the absorbance values for the equilibrium and standard test tubes, respectively. [FeSCN2+]std is calculated assuming all moles of SCN- go to form [FeSCN2+]std as shown below. " My question is; what do they mean by standard test tubes respectively? Are they talking about the container it's being held in? For me it's 10
Given the following standard curve of Absorbance vs Concentration (mM), what in the concentration of Aspirin if the absorbance is 0.822?
A standard curve of absorbance vs. concentration has a linear trendline of y = 0.56x + 0.987. Use this trendline to calculate the concentration of an unknown sample that has an absorbance of 1.245.
In determining the amount of copper and the identity of the copper compound in the unknown sample, a 100-mL solution containing 120.8 mg of the sample was initially prepared. Then, 5.00 mL of this solution was pipetted and diluted with deionized water in another 100-mL volumetric flask. The absorbance of this diluted solution was determined three times at the analytical wavelength. The concentration of Cu is 12.0123 mg/L, what is the mass of Cu in the analyzed solution? the mass of Cu in the unknown sample?
You are measuring the concentration of an unknown protein sample, and the absorbance at 595 nm (or A595) of your unknown is greater than that of the highest-concentration standard solution. It is not advisable to simply extrapolate the line of the standard curve to calculate the concentration of the unknown In this scenario, what would be the best strategy to measure the concentration of your unknown (instead of extrapolating from the standard curve)?
For the determination of Fe3 +, 25 mL of sample taken from sea water is diluted to 100 mL and a quantity of the obtained solution is taken and Fe3 + is determined by atomic absorption spectrophotometer. The absorbance values of the standard and sample solutions are below, and calculate the Fe3 + concentration in sea water in mg / L by drawing the relevant graph.Solution Absorbance1 mg / L Fe3 + 0.04095 mg / L Fe3 + 0.205110 mg / L Fe3 + 0.411615 mg / L Fe3 + 0.620820 mg / L Fe3 + 0.8222Sample Solution 0.5155
The concentration of a dilute aspirin solution is 0.000530 M 0.000530 M . Standard solutions of this compound were used to prepare a Beer's law plot which gives a slope of 1550.1 M −1 1550.1 M − 1 . What is the expected absorbance value for the aspirin solution?
Using the given data compute for the sodium concentration of the patient. Use the same formula in the computation of the concentration using absorbance and concentration of the standard. Standard Absorbance : 0.112 Concentration : 150mmol/L Patient Serum Sample: Absorbance : 0.266 Concentration : ??