A camera tripod is set up as shown below. The tripod is pretty fancy and has self-balancing legs. The camera weighs 47 N. Felicia Filmmaker has positioned the tripod as follows: CA=-4 myA=0 m zĄ = 6 m B = -2 myB = 0 m zB = -6 m xc = 6 myc = 0 m zc = -4 m xD = 0 myD = 12 m ZD = 0 m Python input: X_A = -4 y_A = 0 Z_A = 6 X_B = -2 y_B = 0 Z_B = -6 X_C = 6 y_C = 0 Z_C = -4 X_D = 0 y_D = 12 Z_D = 0 Action! A Z FAD = number (rtol=0.01. atol-1e-05) y D B X Determine the magnitude of the force in each leg of the tripod to keep it in equilibrium: N

A camera tripod is set up as shown below. The tripod is pretty fancy and has self-balancing legs. The camera weighs 47 N. Felicia Filmmaker has positioned the tripod as follows: CA=-4 myA=0 m zĄ = 6 m B = -2 myB = 0 m zB = -6 m xc = 6 myc = 0 m zc = -4 m xD = 0 myD = 12 m ZD = 0 m Python input: X_A = -4 y_A = 0 Z_A = 6 X_B = -2 y_B = 0 Z_B = -6 X_C = 6 y_C = 0 Z_C = -4 X_D = 0 y_D = 12 Z_D = 0 Action! A Z FAD = number (rtol=0.01. atol-1e-05) y D B X Determine the magnitude of the force in each leg of the tripod to keep it in equilibrium: N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the scotch yoke mechanism shown in the figure P4.1, the horizontal position of link 4 canbe described as x = 3 cos (50t + 40°). Determine the displacement of link 4 during theinterval of 3.8 to 4.7 s.
Suppose that the assembled stiffness matrix of question 1 (as shown below) is as follows: [K]=108×a-a0-aa+b-b0-bb where a=4.06 N/m and b=2.28 N/m. If the applied force at node 3 is P=210 KN, find the displacement of node 2 in mm?
MECHANICAL VIBRATIONS USE VIRTUAL WORK HOW DID IT REACH TO THIS ANSWER? THIS IS ACCORDING TO THE ANSWER KEY OF THE BOOK The uniform bar shown in Fig. P3.6 has mass m, length l, and mass momentof inertia I about its mass center. The bar is supported by two springs k1and k2, as shown in the figure. Obtain the differential equation of motion anddetermine the natural frequency of the system in the case of small oscillations.
Consider two robot-manipulators:• A SCARA robot with joints displacement range q1,2 = −90◦...90◦ and q3 = 0..10cm and links lengths L1,2=10 cm.• A Cartesian robot with joint displacements’ range q1,2,3 = 0..10 cm.Which statement is correct?1) The Cartesian robot has a larger workspace.2) It is not possible to judge the workspace based on the information provided.3) Both robots have revolute joints.4) The SCARA robot has a larger workspace.
B-increase of spring coefficient like 0.5 k, 2k, 5k and / orhow does the natural frequency of the system decreasereferencesexternal links
A spring-mass system is shown in the following figure. Use m=3.5 kg and k=100 N/m. a. Determine the static deflection δst . Insert your answer in meters correct up to at least a third decimal place. b. Determine the system period τ. Insert your answer in seconds correct up to at least a third decimal place. c. Determine the maximum velocity vmax which results if the cylinder is displaced 140mm downward from its equilibrium position and released from rest. Insert your answer in m/s correct up to at least a third decimal place.
Spring constant15%, Derive the equivalent spring constant for the system in the figure.
Figure 1.29 shows the suspension system of a freight truck with a parallel-spring arrangement. Find the equivalent spring constant of the suspension if each of the three helical springs is made of steel with a shear modulus G = 100 GPaand has 10 effective turns, mean coil diameter D = 50 cm, and wire diameter d = 5 cm
Mechanical system is shown in the figure. Torque, T(t), is given as an input which is applied ontothe disc and linear displacement of the cart, x(t), is given as an output for the system. The otherparameters and positive directions are given in the figure, also:M is the mass of the cart, J is the inertia of the disk, k is a linear and kT is a torsional springconstants, b is a linear damping constant, β is an angular displacement of the disk.a) At first, draw the necessary free-body diagrams (FBD’s) for the system. Then, identifying theforces with given elements (parameters) in the figure, write all elemental equations used inthe FBD’s. [ Note: Do not ignore the force which shows up on the contact point between thecart and the disc. Note 2: Please pay attention to the positive and negative signs that indicatethe direction.]b) Obtain the equation of motion (EoM) for the system in terms of input & output usingNewton’s Laws (i.e. *Continuity Eqn’s)c) Take Laplace transform of all…
Problem 3: A helical spring is designed to have a stiffness of 500 N/m. The spring has a wire diameter of 5 mm and an outer diameter of 30 mm. Determine the number of coils required for the spring if the spring index is 6. Problem 4: A helical spring is compressed by a force of 100 N, resulting in a compression length of 20 cm. The spring has a wire diameter of 3 mm and a mean coil diameter of 15 cm. Determine the spring constant (stiffness) of the spring.
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
A disk is attached by a spring to a pin. The disk can roll in the horizontal direction and the pin is above it. The spring has an unstretched length of .5m and a spring modulus of 600 N/m The disk has a mass of 20kg and a radius of 200mm The center of the disk is 600mm below the pin and 320mm to the side (so the spring starts diagonal) If the spring is released, what is the speed of the disk when the spring is perfectly vertical? Assume the disk does not slip and is free to spin