A car has mass of 1534 kg is travelling inside a roundabout with speed of 30 km/hr and radius of round about is 50 m. Calculate i) the centrifugal force acting on the car and i) the kinetic energy of the car. i) Angular velocity = rad/sec ii) Centrifugal Force = N. iii) Mass moment of Inertia= Kg-m2 iv)Kinetic Energy =. Joule.

A car has mass of 1534 kg is travelling inside a roundabout with speed of 30 km/hr and radius of round about is 50 m. Calculate i) the centrifugal force acting on the car and i) the kinetic energy of the car. i) Angular velocity = rad/sec ii) Centrifugal Force = N. iii) Mass moment of Inertia= Kg-m2 iv)Kinetic Energy =. Joule.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and 100 cm. Find the distance moved by the load piston if 10 strokes are applied to the effort piston . Given : Stroke length of the effort piston is : 50 cm . Distance moved by Load piston : ____________m
A piston with area 2cm2 is moved at a speed of 1.5cm/s. What is the velocity in m/s if the outlet is 15mm2?
A pulley 1 m in diameter rotating at 300 r.p.m is brought to rest in 80s. By constant force of friction on its shaft. How many revolutions does it moves?
Given the sketch shown below, the diameter of the plunger Dp = 8 cm. The Ram diameter is Dr = 48 cm. The efficiency is 100%, the stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2kN. Find: A) the force f1 exerted on the plunger. B) the number of strokes needed to raise the load given above by a distance of 10 cm. C) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) D) what will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8 cm.
Two workers carry a non-uniform beam weighing 730N. The beam is 2.6m long and its center of gravity is 1.1 m from one end. If the workers hold the beam at its end, how much does each worker lift?
1) volume : 590 2) amount of salt :7.8 3) pumping speed : 6.2
A car starting from rest is accelerated at the rate of 0.646 m/s?. Find the distance covered by the in 23 seconds. The distance covered by the car ( in cm)?
The mass of a fluid system 0.311 slug, its density is 30 lb/ft³ and g is 31.90 fps². Find (a) the specific volume (b) the specific weight, (c) the total volume.
6. A 5 lbm ball starts rolling up a 30deg incline at speed of 20 ft/s. Using conservation of energy, find out how much power(hp) gravity does on the ball when it travels from the bottom to the maximum height considering time consumed is 5s.
Derive dimension of work.
A car weighing 5500 lbm stops at 55 mph. ) a) Energy (in Btu) is dissipated as heat by friction during braking how much? b) Assume all over Vietnam, every day there are 30,000,000 winning processes as above happen. Calculate the average amount of energy (megawatts) expended due to friction?
The rate of water supply to a hydraulic crane is 90 liters per minute at a steady pressure of 70 bars. Find the input power and the efficiency if the output is 7.5 kW. The power in watts is the product of water supply pressure in N/m sq. and volume flow in M' per second.