A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of the screw and the thrust collar mean diameter are known. Running friction coefficients are estimated. Find: (a) Determine the thread depth and helix angle. (b) Estimate the starting torque for raising and lowering the load. . Schematic and Given Data: Load 50 kN

A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of the screw and the thrust collar mean diameter are known. Running friction coefficients are estimated. Find: (a) Determine the thread depth and helix angle. (b) Estimate the starting torque for raising and lowering the load. . Schematic and Given Data: Load 50 kN

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter6: Fasteners

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

(12) A turnbuckle connects two rods having ⅜-16 UNC threads. The thread friction is 0.2. How much external torque is necessary to stress the rods 500lb if it is assumed that neither rod turns as the turnbuckle is tightened? The mean diameter of the threads is 0.335 in.
For a square thread power screw, given that:F= 6.4 kNPitch = 5 mmMajor diameter = 32 mmTotal raising torque = 28 N.mThen then max. torsional shear stress equals:
Design of the Screw Jack. Lifting load – W, kN is 45. Hight of lifting– H, mm is 450 Types of threads is Square Material of nut is Bronze
The flange coupling for two shafts made of plain carbon steel to be connected. The shafts transmitting a toque of 600 N-m. Assume the following permissible stresses for the coupling components: Shaft — Permissible shear stress = 35 MPa Keys — Rectangular formed end sunk key having permissible compressive strength = 60 MPa Bolts — Six numbers made of steel having permissible shear stress = 28 MPa Pitch circle diameter of bolts = 1.6 × Diameter of shaft Calculate: 1. diameter of shaft; 2. Hub length 3. Hub diameter 2. thickness of flange; 3. Diameter of flange 4. Width of key 5. Thickness of key 5. Diameter of bolt; 6. Crashing stress in bolt
In using the formula for measuring an American Standard Unified Screw Thread by the three-wire method, why should the constant 0.86603 be multiplied by the pitch before subtracting from measurement M, even if not enclosed by parentheses? E=M+0.86603P+3W ?
(7) The cylinder head of a 10”x18” refrigerant compressor is attached by 10 stud bolts made of SAE grade 5. The maximum cylinder pressure is 350psi. (a) What size of bolt is to be used? (b) What approximate tightening torque should be applied to induce a tightening stress of 0.9 time of the proof stress?
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m
Please don't provide handwritten solution .... 5.2 Sketch the following thread profiles for a nominal diameter of 25 mm and pitch 3 mm and give their applications: (a) BSW thread, (b) Buttress thread (c) Square thread, (d) ACME thread and (e) Worm thread
4) An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The motor has power rating of 7.5kW & 1,800rpm & has a shaft of 17mm. It will be used to drive a centrifugal pump using cast iron sheave. Design the square key to be used in the assembly based on maximum bearing & shearing stresses of 580MPa & 370MPa, respectively, and factor of safety of 5.
M25x6-4h5h-23 describe this thread
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Draw FBD and determine Stress and Safety Factor of Bicycle Axle (Thru Axel) Specification Weight of cyclist = 120 kg. Materials: Aluminum alloy (AL 6061-T6) Dimension: Length = 122 mm, Diameter = 12 mm, Thread pitch = 1.75 mm, Thread Length = 16 mm.