*** For determining Ixx and setting shape 1 to the blue rectangle, shape 2 to the green, and shape 3 to the orange, fill in the highlighted column. Separate by commas (two), no spaces and two sig figs each.

Q: 17-55. The 100-kg uniform crate C rests on the elevator floor where the coefficient of static…

A: Given data as per the question Mass of crate =100 kg coefficient of friction =0.40

Q: 11. A Carnot engine rejects 80 MJ of energy every hour by transferring heat to a reservoir at 10°C.…

A:

Q: 1- Why When a transformer is loaded with a constant primary voltage, the secondary voltage…

A:

Q: Determine internal energy of steam if its enthalpy, pressure and specific  volumes are 2848 kJ/kg,…

A: Given data h=2848 kJ/kgP=12 MPav=0.017 m3/kg Here, h is the enthalpy, P is the pressure and v is the…

Q: 3.Two Carnot heat engines run in series with the efficiency of first engine is 1/k times the second.…

A:

Q: If you double the size of the larger pad of a hydraulic system, how much less force do you need to…

A: Option (a): 1/4 the force.

Q: Angles (°) Angles (Trial 2) (°) Time (s) Max Height (Ad Max Velocity (V max max Acceleration (a)…

A: Given: Let us consider the given, For Trail 1: Acceleration, a=-8.45 ms Gravity, g=9.81 Net force,…

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

A: When an object is placed under the push or the pull, then it is possible that the shape of the…

Q: The following figure shows an epicyclic gear train (EGT) having two inputs. The sun gear 2 rotates…

A:

Q: please answer quickly

A:

Q: Q4. A/ the ball is thrown from the ground with an initial velocity of v-20i + Viy j, if the range is…

A:

Q: Two uniform spheres are positioned as shown. Determine the gravitational force F which the titanium…

A: mt = 1.20905 kg mc = 47.01512 kg F = ( 9.48294 × 10-8 ) kg

Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a…

A: Given:P1=100 KPaT1=27°CV1=5 m3/srp=10T3=1127°C

Q: n the figure, a flexible belt runs from A over the compound pulley B & back over P to a 200-N…

A:

Q: .A journal bearing is to be used for a centrifugal pump where the shaft diameter is 50 mm and the…

A: Given that, Shaft diameter = D = 50 mm Bearing length = L = 80 mm Ambient temperature = T∞=20 °C…

Q: Describe the changes to the pressure, temperature and velocity of the air as it passes through a…

A:

Q: Consider a modification of the cold air-standard Otto cycle in which the isentropic compression and…

A:

Q: Refrigeration is desired at a Temperature of -5.6°C (minus 5.6 degrees C). Heat is rejected at a…

A: Given   Maximum temperature, Tmax = -5.6oC = 267.4 K   Minimum temperature, Tmin = 36.7oC = 309.7 K…

Q: . What are the Rod and Cone cells in a human eye and describe differences between them in detail?…

A: Rods are one of two kinds of photoreceptive cells found in the retina of vertebrate animals'…

Q: Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator…

A: COP = 5.72

Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…

A: GIVEN DATA- p1 = 100 kPa, T1 = 340 K, and T3 = 4850.3 K, r = 15 and rc = 2. For n = 1.3, cv = 0.718…

Q: Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator…

A: Refrigerant=R22Evaporator temperature, Te=-30oCCondenser temperature, Tc=36oCThe mass flow rate of…

Q: Initially at rest, A Mitsubishi Pajero and a Toyota Vios are connected by a tow cable. The winch on…

A: Given: MA = 2.5 Mg MB = 1.25 Mg L = 5 m Vrel = 2m/s   Note: FBD has not much relevance for this…

Q: [3 4].[5 1]= Not exist O [154] O [12] O [13] O [11]

A: Consider following two matrices A and B - A=Am×n   size of matrix A = No. of Rows×No. of columns…

Q: Solve the following linear programming problems using the simplex method. 1) Maximize Z = X1 + 2x2 +…

A: Given question: We have to maximize z = x1 + 2x2 + 3x3According to   x1 + x2 + x3 ≤ 122x1 + x2 + 3x3…

Q: Find the natural frequencies and mode shapes (mode 1 and mode 2) of the system shown in Figure 1 for…

A: For solution refer below images.

Q: me extrusion die for a polyethylene parison used in blow olding has a mean diameter of 18.0 mm. The…

A:

Q: Steam enters an adiabatic turbine at 3MPa and 500C and exits at 30 kPa. If the efficiency of the…

A:

Q: A flat plate has been placed longitudinally in a stream of crude oil which flows with a velocity of…

A: Length of the plate, L=500 mm=0.5 mWidth of the plate, w=250 mm=0.25 mVelocity of crude oil, U=6…

Q: All collars slide freely. A = 5.0 ft/s downward at the instant shown. Using ICR, determine @AB and…

A:

Q: The motor unit A is used to elevate the 300-kg cylinder at a constant rate of 2 m/s. If the power…

A:

Q: An elliptical plate, major axis 6 units, minor axis 4 units, is submerged vertically until its…

A: Major axis, A=6 unitsMinor axis, B=4 unitsCenter below the surface, h=2 units

Q: Water is flowing in a pipe with radius of 30 cm at a velocity of 12 m/s. The density and viscosity…

A: GIVEN DATA-  PIPE RADIUS R=30cm  VELOCITY V=12m/s  DENSITY =1000kg/m3 VISCOSITY =1.12 Pa.s  WE HAVE…

Q: A specimen with cylindrical shape was subjected to tensile test. Please plot the stress vs. strain…

A: Diameter of test specimen, do=11.600 mmLength of test specimen, lo=50.500 mm

Q: Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator…

A:

Q: A golf ball is launched with the initial conditions shown in the figure. Determine the radius of…

A:

Q: Compute for the vertical reaction at the hinged support at C. Given the following data and figure:…

A: P1=9 NP2=17 NF1=12 Nx=2 mz=5 my=7 m

Q: Q1) Draw the sheering force and bending moment diagrams for fig1 2kN 20KN 10kN 1m 1m 1m FBD 10kN…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: You must design a dust plant. If the grizzly area for which the plant is designed for is 2 x 3 m in…

A:

Q: Q4(a) A 30 kW cooler machine runs at a speed of 4000 RPM One of the bearings is suspected with…

A: A's per the guidelines, we are allowed to solve only first 3 subparts of this question. You may…

Q: he refrigerant flowing through the evaporator in the vapor compression and refrigeration cycle…

A: A vapour compression refrigeration system is an upgraded form of air refrigeration system that…

Q: A specimen with cylindrical shape was subjected to tensile test. Please plot the stress vs. strain…

A: To find: Stress strain plot Young's modulus.

Q: The 15 lb suitcase is released from rest at C. After it slides down the smooth ramp, it strikes the…

A:

Q: 15. To solve Lt sint you may use: nl L (s = a)+¹ 16. Le cos(5t)} = IL (-1)^{t(t)}

A: 15. Given: The function, F(t) = L(t^3sint)

Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a…

A:

Q: A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top…

A:

Q: If the density of a gas is 0.003 slug/ft³, what is the specific weight of the gas? a) 15.2 N/m³ d)…

A:

Q: The figure shows a high-pressure hand pump used for boosting oil pressure in a hydraulic line. When…

A: The hand pump's principle is to create low pressure in order to pull subsurface water. Two or more…

Q: Give the formula for ∆U, ∆H, Q , W, ∆S for the following thermodynamic processes: 1. isothermal 2.…

A:

Q: 18-29. The 10-lb sphere starts from rest at 0= 0° and rolls without slipping down the cylindrical…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.