A certain area is covered by a cellular radio system with 84 cells and a cluster size N. 300 voice channels are available for the system. Users are uniformly distributed over the area covered by the cellular system, and the offered traffic per user is 0.04 Erlang. Assume that blocked calls are cleared and the designated blocking probability is P = 1%. %3D

A certain area is covered by a cellular radio system with 84 cells and a cluster size N. 300 voice channels are available for the system. Users are uniformly distributed over the area covered by the cellular system, and the offered traffic per user is 0.04 Erlang. Assume that blocked calls are cleared and the designated blocking probability is P = 1%. %3D

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter14: Power Distribution

Section: Chapter Questions

Problem 14.7P

See similar textbooks

Similar questions

Suppose two hosts A and B, are separated by 10,000 kilometers and are connected by a direct link of R = 1 Gbps. Suppose the propagation speed over the link is 2.5 x 10^8 meters/sec.a. Calculate the "bandwidth-delay product", R.tprop.b. Consider sending a file of 400,000 bits from host A to B. Suppose the file is sent continuously as one big message. What is the maximum number of bits that will be in the link at any giventime?c. What is the width (in meters) of bit in the link?
Suppose two hosts A and B, are separated by 10,000 kilometers and are connected by a direct link of R = 1 Mbps. Suppose the propagation speed over the link is 2.5 x 10^8 meters/sec.a. Calculate the "bandwidth-delay product", R.tprop.b. Consider sending a file of 400,000 bits from host A to B. Suppose the file is sent continuously as one big message. What is the maximum number of bits that will be in the link at any given time?c. Provide an interpretation of the bandwidth-delay product.d. What is the width (in meters) of bit in the link? Is it longer than a football field?e. Derive a general expression for the width of a bit in terms of the propagation speed s, the bandwidth R, and the length of the link d.
A GSM operator leases 7 MHz of spectrum (i.e., 7 MHz each in the uplink and the downlink), and estimates that a D/R of at least 4 is required. If the cell radius, R, is 2 km (assume hexagonal cells), determine the Erlangs per square kilometer for the network, for a target blocking probability of 1%.
Consider an industrial network application where there is one control unit (PLC) connected using half duplex connection with 20 other sensor and actuator devices having a bandwidth of at least 100Kbps located at the distance of around 2000 feet apart. Choose a most suitable fieldbus protocol and serial communication protocol along with wiring, cable, topology and any other requirement details to connect all these devices efficiently.
Consider a garden house where the radio channel TRT Radyo 4 is constantly open has an installed power of 450 Watt. There will be an average of 10 hours of energy consumption. How many solar panels and batteries are needed?
. Suppose two hosts A and B, are separated by 10,000 kilometers and are connected by a directlink of R = 1 Mbps. Suppose the propagation speed over the link is 2.5 x 108 meters/sec.a. Calculate the "bandwidth-delay product", R.tprop.b. Consider sending a file of 400,000 bits from host A to B. Suppose the file is sent continuouslyas one big message. What is the maximum number of bits that will be in the link at any giventime?c. Provide an interpretation of the bandwidth-delay product.d. What is the width (in meters) of bit in the link? Is it longer than a football field?e. Derive a general expression for the width of a bit in terms of the propagation speed s, thebandwidth R, and the length of the link d
Compare a wireless radio system with a fiber-optic communication system for digitaldata communications over a distance of 1 km. Assume a desired data rate of 75 Mbps. Give pros and cons, advantages and disadvantages, of each. Which one would be better, all factors being considered?
Assume that two hosts are directly connected via a submarine optical fiber cable, which goes from Los Angeles, CA to Shanghai, China. The cable length is 14,000 km. The bandwidth of the cable is R = 100 Gbps. Assume that the signal propagation speed in the cable is 2.0*10^8 m/s. Answer the following questions. (Make sure to have the correct number and unit for your answers whenever applicable.) a. What is the one-way propagation delay, dprop, between the two nodes? b. What is the Round Trip Time (RTT) between the two hosts? c. Calculate the bandwidth-delay product, i.e., R * dprop. d. What’s the meaning of R * dprop?
Q1.Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem in your submission.Consider a client-server system with the following parameters and requirements. The client transmits 10x106 bits of data every minute to the data server connected directly to it. The transmission link speed is 20x106 bps. Each packet is 2,000 bytes long which includes a 20-byte packet header.a. Calculate the number of packets generated per second for data transmission at the client node.b. The system requires every packet must be delivered within 4 ms of generating a data packet. Calculate the maximum link distance between the client and the server that still can meet this requirement. Ignore processing and queuing delays.c. Calculate the number of overhead bits transmitted per second from the client to the server.
A network operator has asked you to design a point-to-point optical link for short reach (2 km) transmission inside a data centre. The operator’s primary concerns are; (i) to minimise capital expenditure (i.e. to keep deployment costs as low as possible) and (ii) to have excellent receiver sensitivity. (a) Draw a block diagram of the optical link you propose, outlining the components used and the reasons for your design choices. (b) Regarding your transmitter design choice: How will electrical information be transferred to the optical domain in your system? And what are the potential drawbacks of this technique? Please use drawings in your answer.
If a total of 33 MHz is allocated to a particular FDD cellular telephone system which uses two 25 KHz simplex channels to provide full duplex voice and control channels, compute the number of channels available per cell if a system usesa) 4-cell reuse, b) 7-cell reuse, and c) 12 – cell reuse. If 1 MHz of the spectrum is reserved for control channels, determine an equal distribution of control and voice channels for all the three cases. [
Consider an AWGN channel with bandwidth 50 MHz, received signal power 10 mW, and noise density No (Noise Power/Bandwidth) = 10−9 W/Hz. (a) What is the information capacity (Mbps) in the system? (3 points, 2 decimal places); (b) By doubling the received power, What is the information capacity (Mbps) in the system? (3 points, 2 decimal places) (c) How much does the capacity (Mbps) by doubling the channel bandwidth? (3 points, 2 decimal places)