A channel of water at a flow rate of 2 kg/ s flowing through a square section and thin-walled channel with a height of 25 mm on the edge the inlet andi outlet are 25 °C and 75 °C respectively, and the channel surface is maintained at a constant temperature of 100 °C. Completely inside the channel approximate the required channel length value, since full-blown flow conditions are in question (m) (cp-4.185 kJ/ups, u=547x10-6Pas, k=0.643 W/ mK, Pr=3.56)

A channel of water at a flow rate of 2 kg/ s flowing through a square section and thin-walled channel with a height of 25 mm on the edge the inlet andi outlet are 25 °C and 75 °C respectively, and the channel surface is maintained at a constant temperature of 100 °C. Completely inside the channel approximate the required channel length value, since full-blown flow conditions are in question (m) (cp-4.185 kJ/ups, u=547x10-6Pas, k=0.643 W/ mK, Pr=3.56)

Name: A channel of water at a flow rate of 2 kg / s flowing through a squar
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A channel of water at a flow rate of 2 kg / s flowing through a square section and thin-walled channel with a height of 25 mm on the edge the inlet andıoutlet are 25 °C and 75 °C respectively, and the channel surface is maintained at a constant temp

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

A straight 10-cm commercial-steel pipe is 1 km long and is laid on a constant slope of 5°. Water at 20°C flows downward, due to gravity only. For water at 20°C, take ρ = 998 kg/m3 and μ = 0.001 kg/m⋅s. Does the flow rate change with the change in the length of the pipe? Yes or No?
A drainage hole (assumed to be a smooth edged orifice) is opened at the bottom of a storage tank full of water. Using Bernoulli’s equation as a starting point, derive an expression that relates the height of water in the storage tank to the volumetric flow rate of water emerging from the orifice.
You are designing a bioreactor that requires turbulent water flow (Re=2300) for better mixing of materials. Your tube diameter is 1.5 inches. What is the minimum volumetric flow rate needed (in in3/s)? **Answer: 7.14 in^3/s
Turbulent Flow of a Power-Law Fluid A pseudoplastic fluid that follows the power law, having a density of 961 kg/m3, is flowing through a smooth, circular tube having an inside diameter of 0.0508 m at an average velocity of 6.10 m/s. The flow properties of the fluid are n′ = 0.30 and K′ = 2.744 N·sn/m2. Calculate the frictional pressure drop for a tubing 30.5 m long.
Two reservoirs, which differ in surface elevation by 40 m,are connected by 350 m of new pipe of diameter 8 cm. Ifthe desired flow rate is at least 130 N/s of water at 20°C,can the pipe material be made of (a) galvanized iron,(b) commercial steel, or (c) cast iron? Neglect minor losses.
Air flows at Q=5 m³/s in a 1-m diameter stainless steel duct (roughness of 0.002 mm) the air properties are (-1.23 kg/m³ and -1.8 x 10^5N-s/m²). Approximate the minimum length of the duct so that entrance lengths can be ignored in the calculation of the pressure drop. a.41.1 m b.206 m c.20.6 m d.0411 Option a is incorrect
For flow of water at 20°C through a straight, smooth pipe at0.06 m3/h, the pipe diameter for which transition to turbulenceoccurs is approximately(a) 1.0 cm, (b) 1.5 cm, (c) 2.0 cm, (d) 2.5 cm,(e) 3.0 cm
Consider the radial flow problem shown in top view where the shaded area represents a damage zone with reduced permeability. Also assume that the system consists of 3 horizontal flow units of equal thickness. The original undamaged permeabilities are 55 md in the top layer, 17.5 md in the middle layer and 28 md in the bottom layer, the reservoir radius is 660 ft, and the damage zone radius is 2.5 ft and well bore radius is 0.3 ft in all three layers. The damaged zones’ permeabilities are all 10.5 md in all three layers. Assume that in each layer and in each section of this system flow is steady state radial in the horizontal plane. Is this system radial series or radial parallel layers ? In order to calculate average permeability of the total system do you average parallel layers first or series layers first? Calculate the average permeability of the total system? Plot the pressure profile from wellbore to the reservoir external boundary for the uppermost layer.
A hose of diameter 3 cm is used to drain a very large tank filled with water (=1000 kg/m3). The hose is draped over the side of the tank so the water is siphoned out. If the hose discharge is 1 m below the surface of the water, estimate the discharged mass flow rate in kg/s? A siphon implies a continuous liquid leg from the water in the tank up the siphon at point 2, the highest elevation, and down to the discharge at point 3. Assume that alpha=1, the discharge at point 3 as well as the tank are both open to the atmosphere and shaft work and frictional losses are ignored. 2.Based on your solution, how can you drain the tank faster?
The reservoirs in Fig. are connected by cast iron pipesjoined abruptly, with sharp-edged entrance and exit. Includingminor losses, estimate the flow of water at 20 °C if the surfaceof reservoir 1 is 45 ft higher than that of reservoir 2.
A surge chamber 10m in diameter is situated at the down stream end of a low pressure tunnel 9.8km long and 2.8m in diameter. At a steady discharge of 32m3/s the flow to the turbine is suddenly stopped by closure of the turbine inlet valves. Determine the maximum rise in level in the surge chamber.
Pressure Drop of Power-Law Fluid in Laminar FlowA power-law fluid having a density of 1041 kg/m3 is flowing through 14.9 m of a tubing with an inside diameter of 0.0524 m at an average velocity of 0.0728 m/s. The rheological or flow properties of the fluid are K′ = 15.23N·sn′/m2 (0.318 lbf·sn′/ft2) and n′ = 0.40. Calculate the pressure drop and friction loss using Eq. (9.1-10) for laminar flow. Check the generalized Reynolds number to make sure that the flow is laminar. Repeat part (a) but use the friction-factor method