I need the answer as soon as possible Mechanics of Materials.Dr. Waleed JasimA circular bar AB with ends fixed against rotation has25 in. -25 in.a hole extending for half of its length (see figure). The outer diameterof the bar is d2 = 3.0 in. and the diameter of the hole is di = 2.4 in.The total length of the bar is L = 50 in.At what distance x from the left-hand end of the bar should a torqueTo be applied so that the reactive torques at the supports will be equal?|A 3.0 in.To

Given:-d1=2.5ind2=3inL=50inTo find:-Distance x

A circular bar AB with ends fixed against rotation has a hole extending for half of its length (see figure). The outer diameter of the bar is dz=3.0 in. and the diameter of the hole is di = 2.4 in. The total length of the bar is L- 50 in. At what distance x from the left-hand end of the bar should a torque To be applied so that the reactive torques at the supports will be equal?

A circular bar AB with ends fixed against rotation has a hole extending for half of its length (see figure). The outer diameter of the bar is dz=3.0 in. and the diameter of the hole is di = 2.4 in. The total length of the bar is L- 50 in. At what distance x from the left-hand end of the bar should a torque To be applied so that the reactive torques at the supports will be equal?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.4.23P: A trimetallic bar is uniformly compressed by an axial force P = 9 kips applied through a rigid end...

See similar textbooks

Similar questions

A vertical pole of solid, circular cross section is twisted by horizontal forces P = 5kN acting at the ends of a rigid horizontal arm AB (see figure part a). The distance from the outside of the pole to the line of action of each force is c = 125 mm (sec figure part b) and the pole height L = 350 mm. (a) If the allowable shear stress in the pole is 30 MPa, what is the minimum required diameter dminof the pole? (b) What is the torsional stiffness of the pole (kN · m/rad)? Assume that G = 28 GPa. (c) If two translation al springs, each with stiffness k =2550 kN/m, are added at 2c/5 from A and B (see figure part c), repeat part (a) to find dmin. Hint: Consider the pole and pair of springs as "springs in parallel."
A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure). Under the action of these torques, the maximum tensile stress in the bar is found to be 6400 psi. Determine the inside diameter rtf of the bar. If the bar has length L = 48.0 in. and is made of aluminum with shear modulus G = 4,0 × 106 psi, what is the angle of twist d (in degrees) between the ends of the bar? (c) Determine the maximum shear strain y (in radians)?
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A solid circular bar of steel (G = 78 GPa) transmits a torque T = 360 N - m. The allowable stresses in tension, compression, and shear arc 90 MPa, 70 MPa, and 40 MPa, respectively. Also, the allowable tensile strain is 220 x 10-6, Determine the minimum required diameter d of the bar, If the bar diameter d = 40 mm, what is Tmax?
Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
The horizon Lai rigid beam A BCD is supported by vertical bars BE and CF and is loaded by vertical Forces P, = 400 KN arid P2= 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (£ = 200 GPa} and have cross-sectional areas Ag=11,100 mm" and ABE= 9280 mm-. The distances between various points on the bars are shown in the figure. Determine the vertical displacements SAand SDof points A and D, respectively.
A plastic rod AB of length L = 0.5 m has a diameter d1= 30 mm (see figure). A plastic sleeve CD of length c = 0.3 m and outer diameter d2= 45 mm is securely bonded to the rod so that no slippage can occur between the rod and the sleeve. The rod is made of an acrylic with a modulus of elasticity E1= 3.1 GPa, and the sleeve is made of a polyamide with E2= 2.5 GPa. (a) Calculate the elongation d of the rod when it is pulled by axial forces P = 12 kN. (b) If the sleeve is extended for the full length of the rod, what is the elongation? (c) If the sleeve is removed, what is the elongation?
A slightly tapered bar AB of rectangular cross section and length L is acted upon by a force P (see figure). The width of the bar varies uniformly From b2at end A to b1at end B. The thickness t is constant. (a) Determine the strain energy U of the bar. (b) Determine the elongation ?? of the bar by equating the strain energy to the work done by the force P.
A trimetallic bar is uniformly compressed by an axial force P = 9 kips applied through a rigid end plate (see figure}. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter of L.25 i n., the brass tube has an outer diameter of 1.75 in., and the copper tube has an outer diameter of 2.25 in. The corresponding modulus of elasticity are f, = 30, 000 ksi, Eb= 16,000 ksi, and E = 18,000 ksi Calculate the compressive stresses ers, ab, and cin the steel, brass, and copper, respectively, due to the force P.
A solid circular bar A BCD with fixed supports at ends A and D is acted upon by two equal and oppositely directed torques T0, as shown in the figure. The torques arc applied at points B and C each of which is located at distance x from one end of the bar. (The distance x may vary from zero to L/2.) For what distance x will the angle of twist at points B and C be a maximum? What is the corresponding angle of twist 0max?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A hollow circular tube T of a length L = 15 in. is uniformly compressed by a force P acting through a rigid plate (see figure). The outside and inside diameters of the tube are 3.0 and 2.75 in., respectively. A concentric solid circular bar B of 1.5 in. diameter is mounted inside the lube. When no load is present, there is a clearance c = 0.0I0 in. between the bar B and the rigid plate. Both bar and tube are made of steel having an c[autoplastic stress-strain diagram with E = 29 X LO3 ksi and err= 36 ksi. (a) Determine the yield load Pt- and the corresponding shortening 3yof the lube. (b) Determine the plastic load Ppand the corresponding shortening Spof the tube. (c) Construct a load-displacement diagram showing the load Pas ordinate and the shortening 5 of the tube as abscissa. Hint: The load-displacement diagram is not a single straight line in the region 0 ^ P ^ Pr