A circular bar of 500 mm length is supported freely at its two ends. It is acted upon by a central concentrated cyclic load having a minimum value of 20 kN and a maximum value of 50 kN. Determine the diameter of bar by taking a factor of safety of 1.5, size effect of 0.85, surface finish factor of 0.9. The material properties of bar are given by : ultimate strength of 650 MPa, yield strength of 500 MPa and endurance strength of 350 MPa.

A circular bar of 500 mm length is supported freely at its two ends. It is acted upon by a central concentrated cyclic load having a minimum value of 20 kN and a maximum value of 50 kN. Determine the diameter of bar by taking a factor of safety of 1.5, size effect of 0.85, surface finish factor of 0.9. The material properties of bar are given by : ultimate strength of 650 MPa, yield strength of 500 MPa and endurance strength of 350 MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.1P: A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness...

See similar textbooks

Similar questions

A bar having a length of 30 in. is used to support an axial compressive loadof 12 kip, Fig. It is pin supported at its ends and made of a 2014-T6 aluminum alloy. Determine the dimensions of its cross-sectional area if its width is to be twice its thickness.
Determine the diameter of a brittle member in inches if the tensile design load is 15,671 lb. assuming a factor of safety of 5 based on an ultimate strength of 60,000 psi.
The steel rod in Fig. is to be used to support an axial load of 18 kip. If Est = 29(103 ) ksi and sY = 50 ksi, determine the smallest diameter of the rod as allowed by the AISC specifications. The rod is fixed at both ends.
Design the spigot (in tension and compression) of the spigot and socket cotterjoint which is subjected to alternate tensile and compressive loading of 50 kN usingthe following data:Yield strength of cotter material SYS = 400 N/mm2, Factor of safety = 4 (for spigot)Assume thickness of cotter, t = 0.30d, where d is the diameter of the rod.
A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 lbf). Determine the minimum required wire diameter, assuming a factor of safety of 2.0 and a yield strength of 860 MPa (125,000 psi) for the steel
helical spring is to support a load of 10 kN. The spring is guided by a rod of 40 mm diameter. The spring undergoes a deflection of 40 mm under the load. Determine the diameter of the wire and the number of turns required. Use steel with a factor of safety 3.
(a) Explain FIVE (5) factors that may influence the optimum column design under an axial compressive load. (b) A 3.6 m long pin-ended column is formed from an A-36 steel circular hollow section with an outer diameter of 75 mm. Determine the minimum thickness, t (to the nearest integer in mm) of the circular hollow section so that the column can safely support the load of 200 kN without buckling. If the outer diameter of the steel circular hollow section is reduced to 62 mm and the ends are pinned-fixed supported, analyse whether the column with the same applied load and the sectional thickness computed above will cause a buckling failure.
13. An airplane’s landing gear must be capable of supporting ⅓ of its weight at 200000 kg. To induce safety, the landing gear must be able to support twice its maximum load. Determine the minimum cross-sectional are (mm2) of the landing gear if it is made of a heat-treated steel having a yield strength of 860 mpa and a tensile strength of 900 mpa.
Refer to the set of bars made of a material with a yield strength of 350 MPa, determine the minimum dimensions h1 and h2 required. Apply a safety factor FS = 1.5 without flux. Each bar is 12 mm thick
A circular bar of 500 mm length is supported freely at its nwo ends. It is acted upon by a central concentrated cyclic load having a minimum value of 20 kN and a maximum value of s0 kN. Determine the diameter of bar by taking a factor of safety of 1.5, size effect of 0.85, surface finish factor of 0.9. The material properties of bar are given by : ultimate strength of 650 MPa, yield strength of 500 MPa and endurance strength of 350 MPa
A circular-cross-section bar with a diameter of 50mm and a length of 1.25 m is axially loaded. The baris made of medium-carbon steel. Both ends are pinned.Determine(a) Whether the Johnson or the Euler formula shouldbe used.(b) The critical load.
A rod is subjed by a compressive load of 60,000 lb with shock. It is made of AISI 3140 OQT 800°F. Determine the diameter of the solid rod in inches based on the ultimate strength.