A circular cylinder of radius 10 cm length 100 cm is rotated clockwise by 10 rad/s . The amount of lift generated is 6 N when air flow approaches the cylinder at V=? ( pi number=3 Air density=1 kg/m3 ) ANSWER:10 m/s

A circular cylinder of radius 10 cm length 100 cm is rotated clockwise by 10 rad/s . The amount of lift generated is 6 N when air flow approaches the cylinder at V=? ( pi number=3 Air density=1 kg/m3 ) ANSWER:10 m/s

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.29P: Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance...

See similar textbooks

Related questions

Q: For a two-dimensional incompressible flow past a flat plate, the boundary layer velocity profile is…

Q: QI: The cart in the figure moves initially at velocity Vo-12 m/s and takes on water with a scoop 80…

Q: A helicopter during a test has its four blades turning at 89 rpm with the blades oriented parallel…

A: Given data:- length of blade=3.5m ρair=1.225 kg/m3 width of blade=200mm…

Q: Consider a blimp that can be approximated as a 3-m diameter, 8-m long ellipsoid and is connected to…

A: Given data: Diameter of blimp, D= 3m Length of the blimp, L = 8m Buoyancy force, FB= 120 N Wind…

Q: A fluid flow with mean speed 2 m/s flow over plate of 2.5 m length has kinematic viscosity 2×10…

Q: A thin flat plate ( 45 cm X 90 cm ) is immersed in a stream of glycerin (P = 1258 kg/m and u = 1.49…

Q: Consider an incompressible flow, laminar boundary layer growing along the surface of a flat plate,…

Q: A ship is propelled by two cylindrical rotors turming at 250 r. p.m. about their axes which are…

Q: Using von Karman momentum integral, derive boundary layer height 8, boundary layer displacement…

Q: 5- Air at 20C is flowing Over a flat plate at 3m/s. If the plate is 30 cm width and at 60 C…

Q: A thin flat plate ( 45 cm X 90 cm ) is immersed in a stream of glycerin (p = 1258 kg/m' and u = 1.49…

Q: A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to…

A: Given Data: The wind speed is: v=15 m/s. The diameter of the cup is: d = 8 cm The density of the…

Q: Experimental studies have shown that the rate of the decay of kinetic energy for homogeneous…

A: Experimental studies have shown that the rate of the decay of kinetic energy for homogeneous…

Q: A two-dimensional diverging duct is being designed to diffuse the high-speed air exiting a wind…

A: (a) The variation of the with x can be expressed as, The density as a function of x can be…

Q: The small boat show in in the figure is driven at a steady speed vo by a jet of compressed air…

A: Given Velocity, Ve = 250 m/s Temperature, Te = 30oC

Q: The two spheres stand with a stop element as in the figure. The spheres are connected with…

A: Given: The specific gravity of steel ball= 5.98 The density of air= 1.225 kg/m3 The density of…

Q: Atmospheric boundary layers are very thick but followformulas very similar to those of flat-plate…

A: Write the properties of air at 20º.

Q: A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to…

A: Given: The diameter of the cup, d = 8 cm The distance of cup from the pivot, L = 40/2 = 20 cm The…

Q: In principle, it is possible to use rotating cylinders as aircraftwings. Consider a cylinder 30 cm…

Q: D. A thin flat plate ( 45 cm X 90 cm ) is immersed in a stream of glycerin (p = 1258 kg/m and u =…

Q: Flow straighteners consist of arrays of narrow ducts placed in a flow to remove swirl and other…

A: Given data L=22cm: 0.22m a=2.7cm=0.027m Uo=11mls μ= 1.85 ×10-5 Pa.s ρ=1.177 kg/m3 To find…

Q: The next figure shows a symmetric two dimensional wedge of half angle of 15°: If the wedge is well…

A: Given: M1 = 3.5 T1 = 20 + 273 = 293K

Q: A thin flat plate ( 45 cm X 90 cm ) is immersed in a stream of glycerin (p = 1258 kg/m and u = 1.49…

Q: Which one of the following is not a flow region where the boundary layer approximation may be…

A: In the flows mentioned above, (a) The jet has a boundary layer in its circumferential region. There…

Q: QI/ If the velocity profile of the boundary layer is =-O find the thickness of boundary Uo 28 layer,…

A: Momentum Thickness,θ=∫0δuu∞1-uu∞dy…

Q: distance of 1 m from the leading edge of a flat plate, kept at zero angle of incidence to the flow…

A: Given:x1=1 mx4=4 mδ1=0.1 cm

Q: Given: Tennis ball, with D=64 mm and m - 579, dropped in standard sea level air. ..nd: (a) Terminal…

A: Given data as per question m=0.057 kgd=0.064 mterminal velocityy will be reached…

Q: The sphere of diameter of 5.0 cm is moving in still water at a velocity of 2.0 m/s. The drag…

Q: An air current impinges laterally on an isolated train car of dimensions 3 m high, 12.2 m long and…

Q: Suppose we wish to analyze the rotating, partly full cylinderof Fig. 2.23 as a spin-up problem,…

A: let's take the cylindrical coordinate system to analyse a rotating cylinder. velocity function V =…

Q: The helium-filled balloon in Fig. is tethered at 20°Cand 1 atm with a string of negligible weight…

A: Write the properties of air at a given temperature.

Q: A spherical particle falling at a terminal speed in a liquid must have the gravitational force…

A: Given data: R=0.7 mm=0.7×10-3 mv=8.16 cms=8.16×10-2 msρs=7.86 gmL=7860 kgm3ρl=0.88 gmL=880 kgm3

Q: A smooth 12-cm-diameter sphere is immersed in a streamof 20°C water moving at 6 m/s. The appropriate…

A: Given: The diameter of the sphere is D=12 cm. The temperature of the water is T=20°C. The velocity…

Q: A flat plate ( 1.5 m) long and ( 1.5 m) wide is towed in water ( p 1000 kg/m and v=1.31 * 10 “m² /s)…

Q: The 2013 Toyota Camry has an empty weight of 3190 lbf,a frontal area of 22.06 ft2, and a drag…

A: Given ,Weight of the Vehicle W = 3190 lbfFrental Area A = 22.06 ft2Rolling Resistance Crr =…

Q: A square plate with edge length 9.10 cm and mass 488 g is hinged along one side. If air is blown…

A: The figure for the flow of air above and below the square plate is shown below. Apply Bernoulli's…

Q: Consider a steel sphere (SG = 7.85) of diameter 2 cm,dropped from rest in the water at 208C. Assume…

A: The drag coefficient is CD=0.47. The diameter of the steel sphere is d=2 cm×1 m100 cm=0.02 m

Q: The cart in Fig. moves at constant velocity V 0 =12 m/s and takes on water with a scoop 80 cm wide…

A: The velocity of the cart is V0=12 m/s. The water scoop has width w=80 cm. The height of the scoop…

Q: Two baseballs of diameter 7.35 cm are connected to a rod7 mm in diameter and 56 cm long, as in Fig.…

A: Given data: The diameter of baseball, db = 7.35 cm. The diameter of the rod, dr = 7 mm. The total…

Q: 8. A flat plate ( 1.5 m ) long and ( 1.5 m ) wide is towed in water (p = 1000 kg/m and v=1.31 * 10 “…

A: The given values are length l=1.5m, width b=1.5m, density ρ=1000kg/m3 , kinematic viscosity…

Q: An excellent approximation for the two-dimensional incompressible laminar boundary layer on the flat…

Q: A new sports car has a drag corfficient of 0.30 and a frontal area of 18.5 ft2, and is traveling at…

Q: A thin sheet of fiberboard weighs 90 N and lies on a rooftop,as shown in Fig. . Assume ambient air…

A: For air density = 1.2 kg/m3. μ=1.8×10-5 Kg/ms Dimension are very large we will assume that the flow…

Q: A portion of ship’s hull can be idealized as a flat plate, 100ft long. If the ship’s velocity is 10…

A: Given data: L=100 ftv=10 ft/sρ=62.4 lbm/ft³µ=3.0 lbm/hr.ft Need to determine the maximum boundary…

Q: 8. A flat plate ( 1.5 m ) long and ( 1.5 m ) wide is towed in water ( p = 1000 kg/m and v=1.31 * 10…

Q: Joe can pedal his bike at 10 m/s on a straight levelroad with no wind. The rolling resistance of his…

A: Given data: The density of air at 20 degrees Celsius is

Q: A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Required information An excellent approximation for the two-dimensional incompressible laminar…

A: Given that, u=U2yδ-2y2δ2+y4δ4 for y≤δWhere,δ=cx12

Q: How do we use the Buckingham pi theorem to prove that drag coefficient is dimensionless?

A: Drag coefficients (Cd) are a measurement of an object's resistance to moving through a fluid. They…

Question

100%

A circular cylinder of radius 10 cm length 100 cm is rotated clockwise by 10 rad/s . The amount
of lift generated is 6 N when air flow approaches the cylinder at V=? ( pi number=3 Air density=1
kg/m3 )
ANSWER:10 m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to measure wind speed. Consider a wind turbine with four 1-cm-diameter cups with a center-to-center distance of 22 cm, as shown in Fig. 1. The pivot is stuck as a result of some malfunction, and the cups stop rotating. For a wind speed of 20 m/s and air density of 1.25kg/m3, determine the maximum torque this turbine applies on the pivot.
A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to measure wind speed. Consider a wind turbine with four 8-cm-diameter cups with a center-to-center distance of 40 cm, as shown. The pivot is stuck as a result of some malfunction, and the cups stop rotating. For a wind speed of 15 m/s and air density of 1.25 kg/m3, determine the maximum torque this turbine applies on the pivot.
Based strictly on your understanding of the flat-plate theoryplus adverse and favorable pressure gradients, explainthe direction (left or right) for which airflow past theslender airfoil shape in Fig will have lower total(friction 1 pressure) drag.
An aircraft with symmetric airfoil of wing area 20 m2, flyingwith velocity 60km/hr experiences lift coefficient of 0.8. Considering the aircraft flying at sea level conditions, determine the mass of the aircraft.
The helium-filled balloon in Fig. is tethered at 20°Cand 1 atm with a string of negligible weight and drag. Thediameter is 50 cm, and the balloon material weighs 0.2 N,not including the helium. The helium pressure is 120 kPa.Estimate the tilt angle θ if the airstream velocity U is (a) 5 m/sor (b) 20 m/s.
flat plate 30 cm by 50 cm slides on oil (μ = 0.8 N⋅s/m2) over a large plane surface. What force is required to drag the plate at 2 m/s, if the separating oil film is 0.5 mm thick?
A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to measure wind speed. Consider a wind turbine with four 8-cm-diameter cups with a center-to-center distance of 40 cm, as shown. The pivot is stuck as a result of some malfunction, and the cups stop rotating. For a wind speed of 15 m/s and air density of 1.25 kg/m3 Using appropriate software, investigate the effect of wind speed on the torque applied on the pivot. Let the wind speed vary from 0 to 50 m/s in increments of 5 m/s. Tabulate and plot the results.
The 2013 Toyota Camry has an empty weight of 3190 lbf,a frontal area of 22.06 ft2, and a drag coefficient of 0.28. Itsrolling resistance is Crr ≈ 0.035. Estimate the maximumvelocity, in mi/h, this car can attain when rolling freely atsea level down a 4° slope.
Consider a blimp that can be approximated as a 3-m diameter, 8-m long ellipsoid and is connected to the ground. On a windless day, the rope tension due to the net buoyancy effect is measured to be 120 N. Determine the rope tension when there are 50 km/h winds blowing along the blimp (parallel to the blimp axis).
In the real flow of air (ρ=1.225 kg/m3) around a cylinder, the circulation is calculated to be 3.97 m2/s. If the free stream velocity is 30m/s, what is the lift generated per meter length of the cylinder? A. 150 N/mB. 160 N/mC. 170 N/mD. 200 N/m
A ship is 125 m long and has a wetted area of 3500 m2.Its propellers can deliver a maximum power of 1.1 MWto seawater at 20°C. If all drag is due to friction, estimatethe maximum ship speed, in kn.