An excellent approximation for the two-dimensional incompressible laminar boundary layer on the flat surface in the given figure is U (2% – 2% + #) for y so, where o = Cx/2, C = const. Layer thickness 8(x) U U = constant u (х, у) /u(x, y) Fir maximum val of v at estatic x-1 m, for the particular case of low, when U= 10.5 m/s ando = 1.1 cm. The maximum value of v is m/s.

An excellent approximation for the two-dimensional incompressible laminar boundary layer on the flat surface in the given figure is U (2% – 2% + #) for y so, where o = Cx/2, C = const. Layer thickness 8(x) U U = constant u (х, у) /u(x, y) Fir maximum val of v at estatic x-1 m, for the particular case of low, when U= 10.5 m/s ando = 1.1 cm. The maximum value of v is m/s.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.55P

See similar textbooks

Similar questions

The thickness of the laminar boundary layer over a flat plate at two different sections Pand Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Q. 6 A 4.5-cm wide space between two plates is filled with SAE 30W lubricating oil at 26.7°C (Hoil = 0.301645 N.S/m2 ). What is the area of a very thin plate which is dragged by a force of 18 N through the oil at velocity of 16 m/min if the plate is 1.5 cm away from one of the fixed surfaces?
Air ( density :1,2 kg /m3 viscosity : 1.5x10-5 m2 /s ) flows over a flat plate of length 2,5 m and width 1 m at a test speed of 1,5 m/s. Determine the approximate magnitude of frictional force, F . (Flat plate is totally submerged in air and both surfaces of it are of same surface quality )ANSWER: F = 0,017955 N
A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is flowing over a flat plate at a stream free velocity of 0.87 m/s. If the plate has a length of 2 m, answer the following: 1.What is Reynolds number at a point that is (1/4)L down the entrance? 2.Is the flow laminar or turbulent? 3.Calculate the thickness of the boundary layer in mm at (1/4)L down the entrance 4.Calculate the drag coefficient at (1/4)L down the entrance
A 0.75 m by3m flat plate is towed at 5 m/s on a 2.5-mm-thick layer of SAE-30 oil at 38°C, with absolute viscocity of 100 cP,that separates it from a flat surface. The velocity distribution between the plate and the surface is assumed to be linear. What force is required if the plate and surface are horizontal?
A 10-cm shaft rides in a 10.03-cm sleeve and 12-cm long, the clearance space (assumed to be uniform) being filled with lubricating oil (? = 0.11 ?? − ?). Calculate the rate at which heat is generated when the shaft turns at 100 rpm in Watts (W). (Rate of energy = Frictional force/resistance x Velocity)
) A 75 mm-diameter orifice is on the verticalside of a closed tank. The tank rests on a flat groundand the orifice is 0.5 m above the ground. Filled withfour fluids with air on the topmost portion that is undera pressure of 15 KPa, and the rest of specific gravities of0.80, 1.0, and 1.50, respectively, the jet hits the groundat a horizontal distance of 3.75 m. If the liquids have thesame thickness, and the power lost in the system is 233watts, determine the following:(a) The initial discharge in L/s if C=0.63.(b) The thickness of each liquid in m.(c) The coefficient of contraction.
Show that the two-dimensional laminar fl ow pattern withdp/dx =0u = U0(1 - eCy)υ =υ0 < 0is an exact solution to the boundary layer equations .Find the value of the constant C in terms of the fl ow parameters.Are the boundary conditions satisfi ed? What mightthis fl ow represent?
describe thickness of the boundary layer in laminarand turbulent flows, Boundary layer separation and methods to avoid theseparation of the boundary layer, and Magnus effect etc
For free flow of air over a plate, it is given that Grashof number is 7 x 10º and Prandtl number is 0.25 Then, determine the type of flow.
a) Which of the following boundary conditions is NOT valid for laminar boundary layer flow over a flat plate along x-axis? y=δ,u=u∞ y=δ,∂u∂y=0 y=δ,∂2u∂y2=0None of the above b)Which of the following condition is true for thermal boundary layer?i Slender body without flow separationii High Reynolds numberiiiHigh Prandtl numberivAll of the above c)Normal pressure gradient is comparable to axial pressure gradient while deriving the boundary layer equations. TrueFalse EXPlain the correct answers dont just mention the correct option