A circular plate, 330 mm outer and 76 inner diameters, is loaded all around its inner edge by a total vertical force P (kN) whilst being simply supported around its outer edge. Determine the distribution of radial bending moment and find the position and magnitude of the maximum value. Take v= 0.27.

A circular plate, 330 mm outer and 76 inner diameters, is loaded all around its inner edge by a total vertical force P (kN) whilst being simply supported around its outer edge. Determine the distribution of radial bending moment and find the position and magnitude of the maximum value. Take v= 0.27.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When a weight of 20 N is added into a hanger in the bending moment experiment, you are getting a reading of 3 kg in the spring balance. The bending moment is calculated as 1130 N-mm. The length of the arm is 145 mm. Calculate the net force in N and the dead weight in N acting in the beam.
A car parking roof with cantilever beam of length 6 m carrying point loads of 12 kN and8 kN at 1.5 m and 2.5 m respectively from the free end and the point loads of 6 kN,3 kNand 4 kN acts at 1.5 m, 2.5 m and 6m from the fixed end. Construct the shear force andbending moment diagram for the beam and also identify the point at which the maximumshear force and bending moment is acting on the beam.
A load of 100 kN, followed by another load of 50 kN, at a distance of 10 metres, advances across a girder with a 100-metre span. Obtain an expression for the maximum bending moment at a section of the girder at a distance of z metres from an abutment. Please provide solutions. Answer is z(140-1.5z) for z< (100/3)m;(100-z)(1.5z-5) for z>(100/3) m.
The beam AB in the figure is balanced from the point a by the simple support from the point B with a sliding support. Accordingly, the absolute value of the bending moment in the section a-a at a distance of 2m from the A end of the beam for the given loading condition in kN.m, which of the following is?
The simple beam AB, shown below, supports a concentrated load of 22 kN and a segment of a non-uniform load varying from 20 kN/m at point C to 40 kN/m at point B.1- Calculate the shear force V and the bending moment M at a cross section located at x = 4.2meters from the support A.2- Draw the shear force and the bending moment diagrams for the beam
Draw the bending moment and shear diagrams for bar CD of the structure below.
The figure shown below shows a horizontal beam that is atbalance, supported at the ends on supports A and B and subjected to thehomogeneously distributed load of 6 kN/m, which acts from top to bottom.low. Considering that the weight of the beam can be neglected, what are the values ofCUTTING FORCE and BENDING MOMENT acting on the cross sectionof the beam 4 meters away from support A?
Calculate the corresponding most unfavorable internal force (bending moment).
6.. A cantilever beam is 2.5 m long, and carries a concentrated load of 380 N at its midpoint, and a uniformly distributed load of 400 N/m over a span from its free end to a point 0.5 m from the free end. Neglecting the mass of the beam itself, draw the shear force and bending moment diagrams for the beam. Show all calculations as well
l4//me shear and bending moment diagram as shown in figure. by graphical method. 132.5KN 122.5KN.m ) sgN/m b itwd L oe—dine—d
Draw the Shear Force and Bending Moment Diagram for the loaded simply supported beam shown below. Ignore the self-weight of the beam
The figure below demonstrates a beamsimply supported, subjected to a loadfixed1177 kn Considering the value of L = 6m, obtainthe diagrams of (a) shear force and (b)bending moment for this beam with thisloading.