Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of "T" Nm. ii) Bending moment of "M?' Nm.

Q: fill out density chart

A: Given: For aluminium: mass→m=0.0122 Kg length→L=0.0222 m Diameter→D=0.016 m Hence volume of the alim...

Q: Knowing that at the instant shown the rod attached at A has an angular velocity of 4 radis countercl...

A: Given that: Angular velocity of the rod attached at A is 4 rad/s and angular acceleration is 2 rad/s...

Q: 1. Determine the value E and of S, using the 2 % offset rule. 25 Aluminum 15 20

A: Given

Q: An oscillating water sprinkler is operated at point A on an incline that forms an angle ß with the h...

A: The motion of an item hurled or projected into the air, subject only to gravity's acceleration, is k...

Q: Determine the conduction resistance of the polyurethane per unit length without the aerogel, in m-K/...

A:

Q: Give 3 examples of a plastic product or component in which creep and stress relaxation would be impo...

A: When subjected to load, materials exhibit an increasing deformation with time, this is called creep....

Q: The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm...

A:

Q: 300 N 36 mm

A: We need to apply force equlibirium equation along the horizontal direction∑Fx=0Ax-C=0......consider ...

Q: What fluid properties are involved in computing for the Reynolds number? Discuss all. Where do you u...

A:

Q: Thickness (in) / (mm) Visible Trans. Visible Refl. Out Visible Refl. In UV Trans. (%) Solar Trans. S...

A: In addition to colourless sheet, the various grades can be ordered in a variety of colours, includin...

Q: A cylindrical metal tube of mean radius r = 5 in., length L = 14 ft, and shear modulus G = 11 x 106...

A:

Q: antages and disadvantages of Natural gas sweetening. Dont writing by

A: High quantities of Hydrogen sulfide or carbon dioxide give rise to Natural gas. The presence of thes...

Q: The specific speed of turbine is 85 rpm and running at 450 rpm. The effective head is 20m and genera...

A:

Q: The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the...

A: To find :  maximum torsional shear stress of a shaft with diameter D can be found at what distance f...

Q: Q2/ Determine the magnitude and direction of a force (P), if the horizontal and vertical components ...

A:

Q: 3.4 Find the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect f...

A:

Q: A three-lobe positive displacement pump pumps 0.3 cubic centimeters of oil on each  love as the pump...

A:

Q: The truss ABC shown in the figure is subjected to a horizontal load P=40 kN. The two bars are identi...

A: Answer: (A) The stress in the member is 100 MPa (Compressive). (B) The strain energy U of the truss ...

Q: A vacuum gage connected to a chamber reads 35 kPa at a location where the atmospheric pressure is 92...

A:

Q: Given a specified level of significance the absolute value of the critical value will be smaller for...

A: A one-tailed test is set up to show that the sample mean would be higher or lower than the populatio...

Q: how does your computations go when for example all needed info are derived as usual and THE SAME FLU...

A:    During solidification, fluid movement is common, which disrupts the above-mentioned solute and he...

Q: A steam with 45 atm and 90 degrees Celsius (enthalpy = 2500 kJ/kg) enter a heat exchanger. Water als...

A: Given: At 45 atm and 90oC: Enthalpy of the steam→hs=2500 KJKg At 5 atm and 10oC:  Enthalpy of water→...

Q: 5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angul...

A:

Q: Q3/ Determine the resultant of the force system shown in Fig. 224 300 30 361

A: It is required to determine the resultant force

Q: t=? A stone is thrown vertically upward and return to the earth in 12 seconds. а. Calculate the init...

A:

Q: F6-11 IE the beam is subjected to a bendiny moment of M = 5 EN- m, delermine the bending stress dvel...

A:

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diameter aluminum specimen hav...

A:

Q: Find the interest amount and future value for the following loan: Principal:6,320 Interest rate: 4% ...

A:

Q: The constant wall thickness of a steel tube with the cross  section shown is 2 mm. If a 600-N m torq...

A: Given data: d=10 mmri=9 mmt=2 mmro=11 mmT=600 N.mG=80 GPa Need to determine the shear stress in the ...

Q: If a particle moves along a curve with a constant speed, then its tangential component of accelerati...

A: It is required to choose correct answer

Q: A dormitory at a large university, built 50 years ago, has exterior walls constructed of L, = 25-mm-...

A: Answer: (a) The heat flux through the original walls is 75.51 W/m2. (b) The heat flux through the re...

Q: A second unidirectional composite also comprises aligned continuous fibres in an epoxy matrix but wi...

A:

Q: A crate of mass 75kg is pushed along a floor with a force of 26N for a distance of 7 m. Calculate th...

A: Mass of crate , m= 75 kg  Force applied, F = 26N  Distance, S = 7m

Q: 2.32 For the setup shown in Fi1gure P2.32, calculate the manometer reading H. () 16 kPa 300 mm Oil S...

A:

Q: A car moves in a straight line such that for a short time its velocity is defined by v= (3t^2+ 2t) m...

A:

Q: One kilogram of water contained in a piston-cylinder assembly, initially at 160°C, 150 kPa, undergoe...

A:

Q: Problem 1. Use INA = Ig + Ad² for moment of inertia. From the beam and loadings shown. a. Compute th...

A: Given

Q: What is the relative humidity

A: To find relative humidity.

Q: lease write a precise overview/description of the precision tweezer below specifically for each part...

A: Given Data : Precision tweezer

Q: TOPIC: Internal Threading or Tapping What are the materials needed in cutting threads by the use of...

A: the main material used for thread cutting is the lead screw. the lead screw is made using high quali...

Q: 11. Determine the matrix representation of each of the following composite transformations. (a) A ya...

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts o...

Q: Steam at 31 kPa is 100% dry but remains at saturation temperature. What is its enthalpy in kJ/kg? (1...

A:

Q: A power cycle operates between two thermal reservoirs at 1200 K and 400 K, respectively. For each of...

A:

Q: (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening i...

A: Since you have asked multiple questions, we will solve the first question for you. If you want any s...

Q: A closed tank contains 0.5 m of mercury, 1.5 m of water, 2.5 m of oil of specific gravity 0.8 and ai...

A:

Q: A 3.5-hp pump delivers 1140 lbf of ethylene glycol at 20°C in 12 seconds, against a head of 17 ft. C...

A: Answer: The efficiency of the pump is 83.90%.  

Q: Car B gaps Car A by 90 ft as they travel along neighboring highway lanes at t = 0. Detemine (a) when...

A:

Q: Homework: Draw S.F.Ds and B.M.Ds for the following beams:

A: Calculate the reaction and moment at the support, RB=6×6+12×6×18-6RB=36+36RB=72 kN MB=6×6×3+12×6×18...

Q: Q6: Horizontal motion of the piston rod of the hydraulic cylinder controls the rotation of link OB a...

A:

Q: To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity durin...

A: It is required to determine convection heat transfer resistance on inside of the pipe per unit lengt...

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.