A circular plate with simply supported edges subjected to a uniform pressure of P=10 KPa, as shown below, is considered. The plate thickness is h=19 mm, and the plate radius is RO=1,340 mm. If Young's modules and Poisson's ratio are assumed to be E=70 GPa and V=0.5, respectively, workout the slope of the plate at the centre. (NOTE: round-off your answer to 4 decimal places, and write your answer without considering any negative (-) sign). Ro

A circular plate with simply supported edges subjected to a uniform pressure of P=10 KPa, as shown below, is considered. The plate thickness is h=19 mm, and the plate radius is RO=1,340 mm. If Young's modules and Poisson's ratio are assumed to be E=70 GPa and V=0.5, respectively, workout the slope of the plate at the centre. (NOTE: round-off your answer to 4 decimal places, and write your answer without considering any negative (-) sign). Ro

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical tank with closed ends is filled with compressed air at a pressure of 500 kPa. The inner radius of the tank is 2 m and it has wall thickness of 10 mm. The magnitude of maximum in-plane shear stress (in MPa) is_______.
A 1.5-m-diameter cylindrical tank is formed of 6-mm-thick sheet steel (E = 200 Gpa, ν = 0.3). The maximum shear strain occurring in this tank when the contents pressure is 1 MPa, is:
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flatbands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa
A cylindrical vessel whose ends are closed by means of rigid flange plate is made of steel plate 3 mm thick. The length and internal diameter of vessel 500 mm and 25 cm respectively. The internal fluid pressure is 3 MN/m2. The value of the change in length is
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
The cylindrical steel tank shown is 3.5m in diameter 5m high and filled with brine solution. Brine has a density of 1198kg/m3. The thickness of the steel shell is 12.5mm. Calculate the tangential stress and the longitudinal stress in the tank, MPa
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.
The gas tank consists of a cylindrical section with two hemispherical endcaps. The cylinder has a diameter of 75 cm and a wall thickness of 2 cm. If the allowable circumferential stress is 150 MPa and longitudinal stress is 100 MPa, find the maximum allowable internal pressure in the tank. Answer: P = ___________________
The tank shown in the figure is fabricated from 10 mm steel plate. determine the maximum longitudinal and circumferential stress caused by an internal pressure of 1.2 mpa
a cylindrical pressure vesssel( diameter =2.8m and wall thickness of 35mm) is made of steel. the maximum pressure inside the tank is 2.0Mpa. Based on the tresca( maximum shear stress criterion) what is the required yield stress of the steel. Show all work. I need an expert to solve it.
A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight density =64⁢ lb/ft3) to a depth of 9750 ft. The internal gage pressure in the tank is 1600 psi. (a) If the allowable stress of the steel is 32 ksi, what is the minimum allowable outside diameter of the tank? (b) What is the maximum tensile stress before the tank is immersed? Determine the external pressure of the seawater at a depth of 9750 ft. po= psi Determine the maximum magnitude of σr produced in the tank. σr = psi Based on the maximum magnitude of σr produced in the tank from Part 2, is there an outside diameter for which the radial stress magnitude will exceed the allowable stress of the steel in this case? More calculations are needed. No Yes For this case, choose the correct statement regarding the maximum magnitude circumferential normal stress. It occurs at the outer surface of the tank, and it is tensile. It occurs at the outer surface of the tank, and it…
A thin metal pipe of mean radius R, thickness t and length L, has its ends closed and is full of water. If the ends are simply-supported, estimate the form of the distribution of shearing stresses over a section near one support, ignoring the intrinsic weight of the pipe. Answer: t = 2450 (RL/t) Show your solution