Answered: A circular shape blank will be cut of…

A circular shape blank will be cut of mm diameter from a strip of mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine The appropriate punch diameter. Blanking force.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter25: Testing And Inspection

Section: Chapter Questions

Problem 25R: What would be the longitudinal shearing strength per millimeter of a specimen that was 50.8 mm wide...

See similar textbooks

Related questions

Q: What is the optimal thickness of a plate sheet that can be punched out if the design stress is about…

A: Yield stress=design stress/factor of safety =200/5= 40psi Shear area=πD*t=π*2*t

Q: 1. The appropriate punch size for a blanking operation using to perform a cold-rolled steel (half…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: What force is required to punch a ½ - inch hole on a 3/8 thick plate if the ultimate shearing…

A: ...

Q: 6 نقاط Bar stock of initial diameter = 90 mm is drawn with a draft = 15 mm. The draw die has an…

Q: What exactly is meant by the term "shearing stress"?

Q: In a rolling operation using a roll of diameter 1.5 m, if a 35 mm thick plate cannot be reduced to…

A: Given data: - The diameter of the roll is D = 1.5 m. The maximum possible reduction is t' = 12 mm.…

Q: Question 3 A rolling operation on a 250 mm wide, 8 mm thick, 1112 cold rolled steel takes place…

Q: Thickness of the plate is reduced from 40mm to 20mm by succesive cold rolling passes using identical…

Q: Products produced by precision forging require Select one: O a. no additional finishing operations…

A: Introduction: Precision forging is defined as a flashless near net shape forging operation which…

Q: A 300 mm thick slab is being cold rolled using roll of 600 mm diameter. If the coefficient of…

A: Given, Thickness of slab=300mm Diameter of roller,D=600mm Radius of roller, R=300mm Coefficient of…

Q: What is the area of the tube? What is the total length of the median line? The shearing stress value…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: 4- A round wire made of a 70-30 Brass (K=900 MPa, n=049 ) is being drawn a diameter of .08 in and…

Q: A strip with a cross section 120 mm x 6 mm is being rolled with 20% reduction area, using rolls of…

Q: A blanking operation is to be performed on 2.0 mm thick cold-rolled steel (half hard). The part is…

A: Write the given data. t=2 mmD=45 mmA=0.075

Q: To draw an aluminum wire with an initial diameter of 8 mm in three passes, up to a diameter of 4 mm.…

Q: Explain the methods of reducing or eliminating springback in bending with proper diagram.

A: When a metal tends to return to its original shape after undergoing tension and compression, that…

Q: A strip with a cross section 120 mm x 6 mm is being rolled with 20% reduction area, using rolls of…

A: Given Strip = 120 mm X 6 mm Deduction = 20% Diameter = 400 mm Coefficient of friction = 0.1 To find…

Q: A strip of thickness 40 mm is to be rolled to a thickness 20 mm using a two-high mill having a rolls…

A: Given data, H1= 40 mm H2 = 20 mm D= 200 mm

Q: Wire is drawn through a draw die with entrance angle a= 17°. Starting diameter is 3.0 mm and final…

Q: An aluminium strip with a cross section of 200 mm × 8 mm is being rolled with 25% reduction of…

A: Given Data: Aluminium strip cross sectional area A=200 mm×8 mm Diameter d=400 mm Tensile yield…

Q: "). A drawing operation is used to form a cylindrical cup with inside diameter = 75 mm, height = 55…

Q: A strip with cross section 120 X 6 mm is being rolled with 20 % reduction area, using rolls of…

A: Consider a strip of thickness h0 is undergone rolling operation whose Roll Diameter is D and angle…

Q: The figure below shows a symmetric plane-strain upsetting process. The process may also be thought…

A: The intiallength of the tube is LiLi=2t+t =3tThe final length of the tube is LfLf=2t+2t…

Q: Illustrate the four basic operations of volumetric deformation. Indicate next to each illustration…

A: Volumetric Deformation.

Q: During pure bending, why there is no shear stress?

A: Bending - Bending of a beam is due to the moment load applied during the loading of the beam.…

Q: Compare the force required to draw (25mm×6mm) capper strip to 45% reduction of area with that…

Q: Calculate the bite angle when rolling plates 12 mm thick using work rolls 600 mm diameter and…

A: Given:∆h, Thickness reducing=3 mmR, radius of roller=300 mm

Q: 2) A 2 mm thick metal sheet is to be bent at an angle of one radian with a bend radius of 100 mm. If…

A: As per given question R = Bend inside Radius=100mmK = 0.5 because R > 2tt = sheet thickness=2 We…

Q: Orthogonal turning of a mild steel tube with a tool of rake angle 10° is carried out at a feed of…

A: Given: Rake angle = 10° Feed = 0.14 mm/rev The thickness of chip = 0.28 mm…

Q: Based on the part information provided in Figure 1: i) Calculate the bend allowance required for…

A: Given: To find: Bend allowance for bend A Angle of forming tool for a spring back of 0.075…

Q: Calculate the bite angle when rolling plates 12mm thick using work rolls 600mm diameter and reducing…

A: Given data: hi=12 mm∆h=3 mmD=600 mm Need to determine the bite angle.

Q: Find the average pressure applied to the workpiece at the end of the stroke

A: for solution refer below images.

Q: A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of…

Q: A 1-in diameter hole is to be punched through a 1/8-in thick annealed titanium-alloy Ti-6Al-4V…

Q: What firce is requure to punch off 5 mm hole out of a 4 mm thick plate if the ultimate punching…

A: Ultimate Punching Stress (Su) = 200 MPa The actual shear stress in the material is τ=F/A; Thus the…

Q: A 150 mm long with 12.5 mm in diameter of a stainless steel rod is being reduced in diameter to 12.0…

A: cutting speed = 0.261799 m/sec material removal rate = 32.7249 cmm/rev cutting time = 0.75 min

Q: In a hydraulic press,Cylinder has a bore area of (342 cm^2)and pressure (205 N/cm^2). Calculate the…

A: Given data: A = 342 cm2 P = 205 N/cm2 Need to determine the weight generated by by the cylinder.

Q: Calculate the force needed to cut two metal parts of 10 mm dia and 15 5 poin mm dia . if the…

Q: 8. To what thickness can a solid cylinder of 1020 steel that is 25 mm in diameter and 50 mm high be…

A: Given: Diameter of the solid cylinder→D=25 mm=0.025 m Height of the cylinder→H=50 mm=0.05 m And…

Q: forming proceɛɛ. 18) rolling mill type are associated with relatively small diameter rolls in…

A: Disclaimer from Bartleby: Since you have asked multiple question, we will solve the first three…

Q: A circular shape blank will be cut of 107 mm diameter from a strip of 3.5 mm with a clearance…

A: Given: Diameter of the blank (D)=0.107m Thickness of the strip (t)=3.5mm Clearance value (C)=0.25mm…

Q: A circular shape blank will be cut of 105 mm diameter from a strip of 3.3 mm with a clearance…

A: Given: Blank diameter DB=105mm Thickness of the strip (t)=3.3mm Clearance value (C)=0.25mm Shear…

Q: What force is required to punch a ½ inch hole on a 3/8 thick plate if the ultimate shearing strength…

Q: The shear strength of a sheet metal is 300 MPa. The blanking force required to produce a blank of…

A: Given data: The shear strength of the sheet metal is τ = 300 MPa. The diameter of the blank is d =…

Q: 2. Calculate the blank size for the following sheet metal bending operation when the thickness of…

A: given data; A=60mmB=250mmC=80mmthickness of sheet (t)=4mmradius of corner (R)=1.5t lets take blank…

Q: A deep drawing operation for a cup is performed in which the inside diameter = 60 mm %3D and the…

Q: A circular shape blank will be cut of 106.9 mm diameter from a strip of 3.49 mm with a clearance…

A: Given The diameter of the blank is d=106.9 mm. The thickness of the strip is t=3.49 mm. The…

Question

100%

A circular shape blank will be cut of mm diameter from a strip of mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine
The appropriate punch diameter.
Blanking force.
Blanking force when the blade angle A circular shape blank will be cut of mm diameter from a strip of mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine
The appropriate punch diameter.
Blanking force.
Blanking force when the blade angle is o.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given data

VIEW

Step 2 Calculate blanking force

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the difference between a transverse face bend and a transverse root bend?
A circular shape blank will be cut of 107 mm diameter from a strip of 3.5 mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine The appropriate punch diameter. Blanking force. Blanking force when the blade angle is 5.70 o.
How is shear obtained?
A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking, Take: Ac-0.06
A blanking operation is to be performed on 2.0 mm thick cold-rolled steel (half hard). The part is circular with diameter 75.0 mm. Calculate the appropriate punch and die sizes for this operation. (Take Allowance coefficient A. = 0.075)
Manufacturer process A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength = 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking. Take: Ac=0.06
create a concise overview of shearing stress with illustration
What force is required to punch a ½ - inch hole on a 3/8 thick plate if the ultimate shearing strength of the plate strength of the plate is 42000 psi and a factor of safety of 2?
A flat-rolling operation of 250 mm wide alloy stee Calculate roll torque
What is the general equation for bending?
Question 1 solid cylindrical work piece is reduced in height by an open die forging process using flat dies on a mechanical press, powered by a 20 kW motor which operates at 35 strokes per minute with a stroke length of 160 mm. The work piece is 60 mm high and 100 mm in diameter and is to be reduced in height by 15%. The coefficient of friction during the operation is 0,18. Calculate the flow stress of work piece material if the press is set to operate at 90% of its maximum capacity.
Prove that: in square key, the crushing stress is equal to twice of shearing stress.