A circular tank of diameter 3 m contains water up to a height of 4 m. The tank is provided with an orifice of diameter 400 mm at the bottom. Find the time taken by water : (a) to fall from 4 m to 2 m. (b) for completely emptying the tank Take Cd= 0.6

A circular tank of diameter 3 m contains water up to a height of 4 m. The tank is provided with an orifice of diameter 400 mm at the bottom. Find the time taken by water : (a) to fall from 4 m to 2 m. (b) for completely emptying the tank Take Cd= 0.6

Name: A circular tank of diameter 3 m contains water up to a height of 4 m.
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A circular tank of diameter 3 m contains water up to a height of 4 m. The tank is provided with an orifice of diameter 400 mm at the bottom. Find the time taken by water : (a) to fall from 4 m to 2 m. (b) for completely emptying the tank Take Cd= 0.6

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

A hemispherical tank of diameter 4 m contains water up to a height of 2.0 m. An orifice of diameter 50 mm is provided at the bottom. Find the time required by water (i) to fall from 2.0 m to 1.0 m (ii) for completely emptying the tank. Take Cd= 0.6
How long will it take the water surface in the tank shown to drop from h = 3 m to h = 50 cm?
The flow of water from a reservoir is controlled by an L-shaped gate hinged at point A, as shown in the figure. The mass of the weight at B (a = 4 m to the right of A, b = 3 m above the base) is 5125 kg. If the gate opens when the water height is 1.75 m above the base, determine the width (in meters, not showing) of the gate.
Find the surface tension of the water droplet of 30 mm diameter when the inside pressure is 3.5 N/m2 The surface tension in N/m is
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
he gage pressure of the air in the tank shown in the figure is measured to be 65 kPa. Determine the differential height h of the mercury column.
Find the force of oil on the top surface CD of the figure below if the liquid level in the open pipe is reduced by 4.0 ft.
A 4-m-long quarter-circular gate of radius 4 m and of negligible weight is hinged about its upper edge A, as shown in the figure. The gate controls the flow of water over the ledge at B, where the gate is pressed by a spring. Determine the minimum spring force (in N) required to keep the gate closed when the water level rises to A at the upper edge of the gate.
A water tank is filled with water to a height of 4.3m above the 10mm diameter orifice which is connected at the side of the tank. How far would the water have traveled horizontally if the orifice is 4.3m above the ground.
The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter 0.3 m is filled with a liquid (SG > 1, like glycerin) and the rest with water, as shown in the figure. The tank is now rotated about its vertical axis at a constant angular speed of ω. Determine (a) the value of the angular speed when the point P on the axis at the liquid-liquid interface touches the bottom of the tank and (b) the amount of water that would be spilled out at this angular speed.
Find the density of a metallic body which flows at the interface mercury of specific gravity 13.6 and water such that 40% of its volume us submerged in Mercury and 60% in water.
Q4: The hydraulic lift in a car repair shop has an output diameter of 30 cm and is to lift cars up to 2000 kg. Determine the fluid gage pressure that must be maintained in the reservoir.