9. AU-tube manometer is connected to a pipe for measuring the pressure of oil SG=0.92 flowing in the pipeline. Mercury (SG=13.6) is used as manometer liquid and the difference of mercury level in the two limbs is 160mm. The center of pipe is 80mm below the level of mercury in the right limb. Determine the pressure in the pipeline and the head. 80 mm 160 mm

9. AU-tube manometer is connected to a pipe for measuring the pressure of oil SG=0.92 flowing in the pipeline. Mercury (SG=13.6) is used as manometer liquid and the difference of mercury level in the two limbs is 160mm. The center of pipe is 80mm below the level of mercury in the right limb. Determine the pressure in the pipeline and the head. 80 mm 160 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A ventury meter used to measure the liquid from the reservoir. The cross-sectional area at the inlet and throat are 4.536 x 10-3 m? and 1.134 x 103 m? with the flowrate of water is 9167 cm¾s. The level difference of mercury in manometer u tube shows the reading of 266 mm. Determine the flowrate coefficient. Given the specific gravity of mercury 13.6.
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
pump with critical cavitation number 0,08 pumps water to a total head of 60 m and temperature of 15°C (Pv=1707 Pa). If the barometric pressure is 98 kPa, head loss in the suction pipe is 1m. Find the maximum value of static suction lift in meters to avoid cavitation in the pump.
In order to measure the pressure difference between two points in a pipeline carrying water, an inverted U tube is connected to the points, and air under atmospheric pressure is entrapped in the upper portion of the U-tube. If the manometer deflection is 0.8 m and the downstream tapping is 0.5 m below the upstream point, find the pressure difference between the two points
Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm diameter pipe at the rate of 102 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 835 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.126 N/mm2. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) (i) the head difference in m of oil (ii) the theoretical discharge in m3/s (iii) the actual discharge in m3/s (iv) the coefficient of…
The figure shows a siphon that is used to draw waterfrom a large open tank. If the absolute vapor-pressureof the water is pv = 1.23 kPa. (a) determine the shortest drop length L of the50-mm-diameter tube that will cause cavitation in thetube. Show all your calculations. (b) Also draw the energy and hydraulic grade lines forthe length of the tube. Be sure to indicate the pressureheads, elevation heads, and dynamic heads. And toshow all your calculations.
A venturi meter is used to measure the flow rate of water at 55 degrees Celsius. The venturi meter has a throat diameter of 75mm, and it is situated in a 250-mm pipeline. A mercury (SG = 13.6) manometer measures the pressure difference, and the reading is 24 mm. Determine a.) the Reynolds number of the flow, b.) the average velocity, c) the volumetric flow rate, and d.) the power loss if 12% of the pressure drop is permanently lost.
In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be 39.8 ft3 /s. The leakage into the tailrace was found to be 1ft3 /s. The elevation of the centerline of the shaft above, the surface of tailwater was 12.67ft. The diameter of the turbine intake was 30in and the pressure at this section was measured by a mercury U-tube. The readings in the two sides of the mercury U-Tube were 10.556 ft and 0.900 ft, the zero of the scale being at a level 3.82ft below that of the centerline of the turbine shaft. The generator output was 391.8 kW, friction and windage loss 13.8 kW, iron loss 2.0kW and armature loss of 4.4kW. The specific gravity of the mercury used was 13.57. Calculate the efficiency of the turbine.
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
Determine the available suction head of a pump that is taking gasoline at 204 deg. C, from a closed tank with a pressure of 585 Kpa gage. The specific gravity of gasoline is 0.78 and its vapor pressure is 620 kpa absolute. The loss in the suction pipe is 0.5m and the pump centerline is located 3.60 meters above the gasoline level. answer is 4.47 how
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.