A clay tile V-shaped channel of included angle 60° isflowing at 1.98 m3/s on a slope of 0.33°. Is this a mild,critical, or steep slope? What type of gradually variedsolution curve are we on if the local water depth is (a) 1 m,(b) 2 m, or (c) 3 m?

Q: A clay tile V-shaped channel, with an included angle of90°, is 1 km long and is laid out on a 1:400…

A: Given data:

Q: A rectangular concrete channel 4.5 m wide is carrying water. At an upstream point, the depth of…

A: Given: Wide, b= 4.5 m  Depth at upstream , d1 = 1.5m  Depth at downstream,d2 = 1.17 m  Length, L=…

Q: Water fl owing in a wide channel 25 cm deep suddenlyjumps to a depth of 1 m. Estimate (a) the…

A:

Q: It is desired to excavate a clean-earth channel as a trapezoidalcross-section with θ = 60°. The…

A: Write the formula for the value of depth using the formula for half-hexagon. Calculate the value of…

Q: a) A rectangular channel 3 m wide carries at a depth of 2 m. i) Is the flow subcritical or…

A: Given:- Width = w = 3m Assuming the Velocity △V=10m3/s Depth =h =2m To Find:- 1) Subcritical or…

Q: Water is to be transported at a rate of 10 m3/s in uniform flow in an open channel whose surfaces…

A: Given data Volume flow rate = 10m3/sec To determine the best cross section if the shape of the…

Q: Water flows uniformly half-full in a 3.2-m-diameter circular channel laid with a slope of 0.004. If…

A: Given data: Since the channel is half full: Semi cross-section area of the channel is given by…

Q: Water at 65°F flows at a depth of 1.4 ft with an average velocity of 10 ft/s in a wide rectangular…

A: (a) The Froude number is

Q: A new, finished-concrete trapezoidal channel, similar toFig. 10.7, has b =8 ft, yn = 5 ft, and θ =…

A: Given data Trapezoidal of of base b =8ft Depth of the channel yn = 5ft Discharge througth the…

Q: Q(1): A power canal of trapezoidal section has to be excavated through hard clay at least cost.…

A:

Q: Water at 65°F flows at a depth of 1.4 ft with an average velocity of 20 ft/s in a wide rectangular…

A: Write the expression of the Froude number.

Q: At what depth will water flow in a 4 m wide rectangular channel if n=0.018, S0=0.0009, and Q=7m^3/s?

A: Givenb=4 mn=0.018S=0.0009 Q=7 m3/s

Q: Water flows in a 9-m-wide rectangular open channel at a rate of 55 m3/s. If the flow depth is 2.4 m,…

A: Write the formula for Froude number in terms of flow depth, width, and flow rate for the given…

Q: Water, at 20°C, is flowing steadily in a 0.4-m- wide rectangular open channel, made of corrugated…

A: Here we haveb=0.4Q=0.2 m3/sy=0.15 mNow,          A=bxy=0.4 x 1.5 =0.06 m2Flow velocity…

Q: ischarge is 875 ft/s and the normal depth ar culated to be 1.0 ft and 54.7 ft/s, respect lepth and…

A: given:Q=875ft3/sB=16ft

Q: A 6m rectangular channel channel carries a discharge of 30 m³/s at a depth of 2.5m. Determine the…

A: Given: The discharge carried by channel, Q = 30 m^3/s The depth of channel, d = 2.5 m The length of…

Q: A trapezoidal channel transports water to supply a township. The longitudinal bed slope is 0.0077.…

A: First draw the cross-sectional diagram of the trapezoidal channel,

Q: The flow rate in a 3-m wide rectangular channel on a slope of 2 percent is 11 m/s. The Manning's…

A: The immediate advance technique is proposed to supplant the calculations by experimentation utilized…

Q: Water flows full in an asphalt half-hexagon channel ofbottom width W. The flow rate is 12 m3/s.…

A: Given: The flow rate, Q = 12 m^3/s The Froude number, Fr = 0.6   If the side of a trapezoid is ‘s’…

Q: The trapezoidal channel of Figure 6 is made of brick work and slopes at 1:500. Using Manning…

A:

Q: dal section, the mos

A: given::

Q: Water is flowing uniformly in a rectangular open channel with unfinished-concrete surfaces. The…

A: Calculate the cross-sectional area of the channel. AC=by Here, b and y are the flow width and flow…

Q: A brick rectangular channel with S0 = 0.002 is designed tocarry 230 ft3/s of water in uniform flow.…

A: Given data: Rectangular channel So=0.002 discharge (Q)        = 230 ft3/s determine  Percentage of…

Q: Water flows in a rectangular open channel of width 0.6 m at a rate of 0.25 m3/s. If the flow depth…

A: Given, b = 0.6 m Depth (y1) = 0.2 m Volume flow rate = 0.25 m3/s g = 9.8 m/s2

Q: A gravelly rectangular channel, 7 m wide and 2 m deep, isflowing at 75 m3/s on a slope of 0.013. (a)…

A: Given data: The width of the rectangular channel is b = 7 m. The depth of rectangular channel is y…

Q: Consider uniform flow through a wide rectangular channel. If the bottom slope is increased, the flow…

A: Solution:

Q: A triangular channel (see Fig. ) is to be constructed ofcorrugated metal and will carry 8 m3/s on a…

A: To find:- (a) the bestincluded angle θ for the channel, (b) the normal depth forpart (a), and (c)…

Q: A circular corrugated-metal water channel has a slope of1:800 and a diameter of 6 ft. (a) Estimate…

A: The area and hydraulic radius are given in the text:…

Q: Problem 1. A 4 m wide channel with a rectangular cross-section is carrying a flow with flow rate Q =…

A: Froude number (Fr) is a dimensionless number. Froude number (Fr) is defined as ratio of the inertia…

Q: Consider the uniform flow of water in the triangular channel shown in the figure. The channel bed…

A: Write the expression of the normal depth. Q=1nAR2/3S

Q: Figure shows a horizontal flow of water through asluice gate, a hydraulic jump, and over a 6-ft…

A: Discharge,Q=cdHb2gy1Coefficient of…

Q: The trapezoidal channel of Fig. is made of brickworkand slopes at 1:500. Determine the fl ow rate if…

A: For brickwork,  n ≈ 0.015. Evaluate the hydraulic radius with y = 0.8 m:…

Q: Water flows in a rectangular channel at a depth of y₁ = 0.2 m and a flow rate of 7.5 m³/s. A…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: A rectangular channel is 2 m wide and contains water 3 mdeep. If the slope is 0.85° and the lining…

A: Given data: Width of the rectangular channel, b = 2 m. Depth of water, y = 3 m. The angle of…

Q: A rectangular channel, laid out on a 0.5° slope, delivers afl ow rate of 5000 gal/min in uniform fl…

A:

Q: A trapezoidal channel with a bottom width of 6 m, free surface width of 12 m, and flow depth of 1.6…

A: The cross-sectional area, A=(12+6)(1.6)/2=14.4m2. The perimeter of channel, P=6+232+1.62=12.8m

Q: Water at 10°C flows in a 6-m-wide rectangular channel at a depth of 0.55 m and a flow rate of 12…

A: Given data b=6 mQ=12 m3/secy=0.55 m

Q: Water flows uniformly in a rectangular channel with finished-concrete surfaces. The channel width is…

A: According to the given conditionCross sectional flow area is given asA=ybA=1.2×3A=3.6 m2and wetted…

Q: 7. A long triangular open channel with two different side slopes, these are: 2:1 and 3:1 (H: V). The…

A: option D i.e 19.9 & 37.3 is the correct answer

Q: In flowing from section (1) to section (2) along a rectangular open channel, the water depth…

A: Consider section 1 of the rectangular open channel. Consider the water depth and velocity at section…

Q: If a rectangular sharp-crested weir 1.25m long with no end contractions were to replace the…

A: For rectangle weir discharge is given by Q=23Cd×L×2g×H32 where Cd=co-efficient of dischargeL=length…

Q: A gravelly earth-wide channel is flowing at 10 m3/s per meterof width on a slope of 0.75°. Is this a…

A: The discharge is q=10 m3/s. The slope is θ=0.75°

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.