A closed container contains 2.4m high of oil (SG = 0.8), 1.5m high of water, a 1m high of an unknown liquid (SG = 2.8), and the air above these mixture has a pressure of 43 KPa. Determine the pressure at the bottom of the tank.

Q: Read the Rice Tariffication Law and other reading materials given. Give your opinion on the advantag...

A:     For decades, the rice market was dominated by the National Food Authority (NFA), whose exclusive...

Q: A model of a hydraulic turbine is tested at a head of 1/4th of that under which the full scale turbi...

A: Given: The head of model, Hm = Hp/4 The diameter of model, dm = dp/2

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2 ...

A: Find the magnitude of reactive force at point O

Q: A 16-cm diameter copper ball is to be heated from 100°C to an average temperature of 150°C in 25 min...

A: Given Data D=16 cm Ti=100°C Tf=150°C C=0.395 kJ/kgK

Q: -rce. What is the best angle?

A: To find angle.

Q: The cantilever beam AC shown in the figure is subjected to a load 1kN at the end A, and an in- plane...

A:

Q: A stone is just released from the window of a train moving along a horizontal straight track. The st...

A:

Q: Problem Solving - Solve what is required. and highlight your final answer in two decir PICK 3 PROBLE...

A:

Q: find the magnitude of T and its direction (0) for which the eye bolt under a resultnea donnid of 15K...

A:

Q: Express the boundary conditions on each boundary for each problem shown below. y

A: To find  Boundary conditions  

Q: determine the size of the punch,

A: Given data; For a circular blanking operation;Size of the blank=30 mmThickness of the sheet, t= 3 mm...

Q: Steam enters an adiabatic turbine operating at steady state with an enthalpy of 3251.0kJ/kg and leav...

A:

Q: What is indicated by a LTFT reading of 24 percent?

A: Given Data : LTFT

Q: The 12-Mg truck drives onto the 396-Mg barge from the dock at 17 km/h and brakes to stop on the deck...

A: For solution refer below images.

Q: The length of a cylindrical pressure vessel is 4 m. The ends are closed with flat plates. When subje...

A:

Q: A 8.7-Mg truck is resting on the deck of a barge which displaces 235 Mg and is at rest in still wate...

A:

Q: the parabola y=x^2 in the x-y plane is

A: Given; From figure are enclosed between the straight line y=xand the parabola y=x2 The given curves ...

Q: Water is fed to an inward flow reaction turbine, running at 180 rpm with a velocity of flow of 3 m/s...

A:

Q: - A rectangular plate simply supported along its edges and subjected to a uniform of intensity po: 1...

A: Givenuniform load =Pob=2aw=0.01013

Q: The LiBr-water absorption cycle shown in Fig. 17-2 operates at the following temperatures: generator...

A: Find the concentration of Li-Br in the generator Tg=100°C Tc=55°C Te=10°C Ta=30°C

Q: Which of the following statement is/are true? The velocity of projectile motion in (A) maximum heigh...

A: It is required to determine choose correct Answer

Q: A supersonic aircraft flies at an altitude of 3000 m. An observer on the ground hears noise generate...

A: Velocity of Sound,V=3000m×212s⇒V=353.55msTotal distance traveled by aircraft before the observer hea...

Q: The torque exerted by a shaft in a Prony brake with an arm length of 1.85-feet and the scale reading...

A: force(F)=250lb Arm length(d)=1.85ft

Q: Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate o...

A: Given Data  Weight W = 70 Kg  Spring rate for spring 1= 0.209 Kg/mm  Spring rate for spring 2 and 3=...

Q: Explain the significance of Fluid friction damping in an indicating Instrument.  Diagrams – draw ne...

A: Fluid friction damping: This form of damping is similar to air damping but oil is used in the place ...

Q: experimental rocket sled weighs 5000 lb and is propelled by six rocket motors each with an impulse r...

A:

Q: A pulley is keyed to a 2.5 in diameter by means of a 5/8’’ x 7/16’’ x 3’’ flat key. The allowable be...

A:

Q: The small collar of mass m = 0.71 kg is released from rest at A and slides down the curved rod in th...

A: GIVEN DATA - MASS m=0.71kg h=2.29m WE HAVE TO FIND VELOCITY AT B POSITION CONCEPT USED - ENERGY BALA...

Q: Find the second moment of area, the location of the neutral axis, and the distances from the neutral...

A: The given cross-section is : Mz =1.13 kN-m

Q: The cross-sectional dimensions of a beam are shown. Assume b=3.625 in., t=tw=0.1875 in. and d=4.125 ...

A:

Q: Continue from Question 1. The composite bending rigidity E El is approximately: steel 15 mm aluminum...

A:

Q: Discuss Flexure, Shear and Deflection.

A: Flexure : The members those experiences primarily bending stresses such as beams is called as Flexur...

Q: Use Bernoulli's Equation. A jet of water issues out from a nozzle fitted at a height of 4m from the ...

A:

Q: The plates of thickness 1.5mm is joint by two 3.0mm diameter rivets as shown in the figure. Calculat...

A:

Q: A single-acting, single-cylinder air compressor is rated at 4.25 (m)^3/min of air. The suction condi...

A:

Q: For a thin-walled hydraulic cylinder (where pressure is retained by a movable piston), and a long pi...

A: As per given question  We have determine force due to longitudinal stress

Q: Is the energy required to heat air from 295 to 305 K the same as the energy required to heat it from...

A:

Q: If the bucket and its content have a mass of 10 kg and are suspended from the cable by means of a sm...

A:

Q: down about point (A) by Z

A:

Q: is the simplest type of motion and is along a straight line path. * O curvilinear motion rectilinear...

A:    Motion is defined as a body's free movement with regard to time. For example, a fan, dust droppin...

Q: Consider a sealed, rigid container of 10 kg of water vapor at 25°C and 80 kPa. A paddle wheel with a...

A:

Q: Show complete solution and FBD. 3 decimal points.  Three bars pinned together at B and C and suppor...

A: Draw the free-body diagram of bar BC.

Q: A light fixture of negligible mass, has three applied forces acting on it as show |F,| = 4 kN 1.2 m ...

A:

Q: The 19-Mg truck hauls the 40-Mg trailer. If the unit starts from rest on a level road with a tractiv...

A:

Q: 2. Show that the gravitational self-energy (energy of assembly piecewise from infinity) 3GM? of a un...

A:

Q: Q4. Balloons are often filled with helium gas (Figure 4) because it weighs only about one-seventh of...

A:

Q: Heat transfer Question Please explain how to write an excel spreadsheet that will calculate the temp...

A:

Q: The cross section of a composite beam is shown below. The Young's modulus of steel is 200 GPa and fo...

A:

Q: A platinum disc aboard the International Space Station has a thickness of 6 in. and a diameter of 2 ...

A:

Q: shear stress in the body there will be

A: Given; An elastic body is subjected to a tensile stress X in a particular direction and a compressiv...

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.