A closed thermodynamic system undergoes a cycle comprising four processes 1- 4. The following amount of heat is transferred through the system boundaries: Process 1: 50 kJ heat added to the system Process 2: 80 kJ heat removed from the system Process 3: 100 kJ heat added to the system Process 4: 40 kJ heat removed from the system What is the net work done in this cyclic process?

Q: 3. What are the differences between pressure sensor, pressure gauge and pressure transmitter? Explai...

A:

Q: We have the following state space model: *1 = 4x1 – 16x2 + 10u1Uz *2 = 3x3 – 9uz y = 5x1u2 + 3x2u1 a...

A:

Q: 1. You serve a volleyball with a mass of 2.1 kg. The ball leaves your hand with a speed of 30 m's. T...

A:

Q: An experiment is conducted on the surface of the planet Mars. Assume an isothermal atmosphere, where...

A:

Q: Find: 1-- Displacement 2- Velocity 3-Acceleration for slider crank When, ? = 100 rad/???2 R=6.3cm L=...

A: α=100 rad/sec2R=6.3 cm ,L=26.1 cmn=LR=26.16.3=4.142θ=150°ω=100 rad/sec

Q: 2- A compound shaft consists of two segments. Segment (1) is a tube with a length of L, = 500 mm, an...

A:

Q: hése are statements regarding the process of measurement. Select all that are True. O Two different ...

A:    Measuring is, by definition, the process of comparing the value of whatever we see to some standa...

Q: 8. The potential energy of an apple is 6.00 joules. The apple is 3.00-meters high. What is the mass ...

A:

Q: Observe the figure below. Determine the following: a. axial stress on the shank if the load applied ...

A:

Q: The problem involves a cylinder falling inside a pipe that is filled with oil as depicted in the fig...

A: The given pipe is as shown below,  

Q: 1. You serve a volleyball with a mass of 2.1 kg The ball leaves your hand with a speed of 30 m's. Th...

A: Given data : Mass=m Velocity=V Acceleration due to gravity=g   To find : Type of energy and its valu...

Q: A car P travels along a straight road with a con- stant speed v = 65 mi/hr. At the instant when the ...

A:

Q: what is its °API? How much will it weigh per gallon?

A:

Q: A constriction in a pipe will cause velocity to increase and pressure to fall at the throat. The pre...

A:

Q: Which of the following statements about vehicles that are subject to Diesel Opacity Emissions (Smoke...

A: According to the terms, all vehicles registered outside DEMA with MGW of 8500 lb will not require an...

Q: If the journal bearings at A and B exert only horizontal and vertical forces on the shaft, determine...

A:

Q: f a material can absorb radiation, what aerospace material property is demonstrated

A:    Radiation heat transfer is a process in which heat waves are released and then absorbed, reflecte...

Q: The compressive strength of aramid fiber is about one-eighth of its tensile stress. Estimate the sma...

A:

Q: Under the right conditions, it is possible, due to surface tension, to have metal objects float on w...

A:

Q: A cam drive is used for a mechanism that moves a tool in an automated screw machining process. The c...

A: Given that: Cam follower rise outward 24 mm with harmonic motionin 0.25, dwell for 0.35, fall 10 mm ...

Q: ucceleration(in m/

A:

Q: Explain the relationship between the answers for (a) and (b).

A: we have to determine the saturation pressure of liquid water  & vapor @ 100 Celcius

Q: Determine the reactions at supports A, C,

A: Need to determine the reactions At supports A,C and D  

Q: a material can absorb radiation, what aerospace material property is demonstrated

A:    Radiation heat transfer is a process in which heat waves are released and then absorbed, reflecte...

Q: he company is also interested in expanding its production capability into composite based products....

A:    Filament winding is an automated open moulding method that employs a revolving mandrel as the mou...

Q: 1. You serve a volleyball with a mass of 2.1 kg The ball leaves your hand with a speed of 30 m's. Th...

A:

Q: A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σ...

A: We have given a stress element which consist a biaxial loading σx = 8 MPa in X direction, σy = 4 MPa...

Q: Q.13 The following specifications are glven for a rigid coupling. Outside diameter of flanges = 160 ...

A:

Q: Find the dynamic and kinematic viscosities of kerosene,

A: We need to find dynamic & kinematic viscosities of kerosene SAE 10W-30 motor oil and water ( T=3...

Q: Find the force in members AB, AC, BC, Bd, CD and CD for truss shown in Fig 4-3.17. Assume that the l...

A:

Q: The heat-transfer rate to the surroundings from a person at rest is about 100 W. Suppose the ventila...

A: Internal energy is the amount of energy possessed by the molecule of the body . here the air is bein...

Q: Design a single riveted lap joint to connect two mild steel plates, 14.5 mm thick, the joint being d...

A: We will consider maximum shear stress criteria and maximum crushing stress criteria for the design, ...

Q: For the crank- slide mechanism. B slides 03 along 0203 link making 300mm stroke, as shown in Figure....

A:

Q: Part A The 150 lb man bes against the cushion for which the coefficient of static fricton is , 05 He...

A:

Q: Proplem the Determine the principal stress, lane shear werage 20 MPa non re or 80 MPa ar case). 30 M...

A: Given data : Normal stress in X direction (σX)=30 MPaNormal stress in Y direction (σY)=-20 MPaShear ...

Q: velocity method to graphically determine the linear velocity of the package as the crank rotates clo...

A: Given  Figure of package moving device   To find Linear velocity of the package for clock-wise rotat...

Q: The vacuum at the steam inlet to a condenser was found to be 716 mm of Hg and the temperature of ste...

A:

Q: and exits at 50°C. The value of the Log Mear outside of a tube. Cold enters the tube at 20°C Saturat...

A: Given:Thi=100o CThe=100o CTci=20o CTce=50o C

Q: n a composite slab, the temperature at the interface (Tinter ) between two materials is equal to the...

A: Given: A composite slab

Q: what happens to the hydrostatic force imposed by the liquid to the tank wall when the tank is closed...

A: In this question we are required to explain about the hydrostatic force imposed by the liquid on the...

Q: ding mome

A:

Q: A pulley with a diameter of 4 in. can rotate about a fixed shaft with a diameter of 2 in. The coeffi...

A: (a) Draw the free body diagram of the pulley to raise the load.

Q: 1.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system too...

A:

Q: . In the casting of steel under certain mould conditions, the mould constant in Chvorinov's rule is ...

A: Given:Mould constant, C=4 min/cm2Dimension of plate=25×8×2.5 cm3n=2

Q: | 90 kN 190 kN D EV |B For the beam and loading shown, determine the deflection at S250 x 37.8 point...

A:

Q: he piston cylinder system shown below contains R-410a at 20°C and 100 kPa. If the temperature of the...

A: Given:R-410aT=210°CP1=100 kPaT2=50°C

Q: 3: Water flows through a 100 mm diameter pipe at velocity of 4.5m/sec. Find the discharge.

A: Given:d=100 mmV=4.5 m/s

Q: first 20 cm o wer it comple

A:

Q: 4. The bicycle and rider have a combined weight of 240-lbs acting at G. The coefficient of static fr...

A:

Q: Why is the design of this Supersonic Diffuser totally wrong?

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.