Q.13 The following specifications are given for a rigid coupling.Outside diameter of flanges= 160 mm ·Diameter of recess= 95 mmmNumber of boltsPrelond of each bolt10 kN%3DCocfficient of friction= 0.15Specd of rotationThe bolts are set in large clearance holes calculate power transmitting capacity ofcoupling.= 100 rpm%3D

Answered: Image /qna-images/answer/f772ebf1-4b4b-4c6e-84ee-e5e926e9b9a0.jpg

Q.13 The following specifications are glven for a rigid coupling. Outside diameter of flanges = 160 mm Diameter of recess = 95 mm Number of bolts Preload of cach bolt = 10 kN Coefficient of friction = 0.15 %3D Speed of rotation The bolts are set in large clearance holes calculate power transmitting capacity of coupling. 100 rpm %3D

Q.13 The following specifications are glven for a rigid coupling. Outside diameter of flanges = 160 mm Diameter of recess = 95 mm Number of bolts Preload of cach bolt = 10 kN Coefficient of friction = 0.15 %3D Speed of rotation The bolts are set in large clearance holes calculate power transmitting capacity of coupling. 100 rpm %3D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Similar questions

8. Design a clamp coupling for transmitting 25 kW at 300 rpm. Allowable shear stresses in shaft and key are 50 MPa and 45 MPa, respectively. The number of bolts joining the two halves of muff is 4. The permissible tensile stress in the bolt is 70 MPa and the permissible crushing stress in the key is 90 MPa. The coeffi cient of friction between the muff of the CI and the shaft of steel is 0.20.
6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples .
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
M16 (h=2mm, d1=13.54mm, d2=14.7mm) material quality 8.8 bolt-nut connection Blowout= 2500 daN prestressbored with. Factor of safety S=2.5, key length L=10.d, coefficient of friction µo='=0.17; Average of contact surface with nutdiameter is given as d0=1.4.d. According to the given;a) strength control calculation during tightening;b) hand force that must be applied to the wrenchc) When the pre-tensioning force is applied, the elongation of the part is given as lp= 0.015mm, and the elongation of the bolt as lc= 0.030mm. BusinessSince the total elongation of the bolt is lctop=0.040mm for Ftop=3000 daN after the force is applied, we can define the characteristic of the bolt.find it.d) the characteristic of the part and the minimum remaining shortening value önlp after the prestressing forcee) Calculate the portion of the operating force on the bolt (Fic) and the part (Fip).f) Calculate the pre-tension force Fön' value remaining in the connection after the operating force has been…
A nut which is connected to a lead screw is moved in a horizontal plane against a force of 100kN at a speed of 4mm/sec by electric motor powered screw. The following data is given Single start square thread screw Pitch of the screw = 6mm Outlet diameter of the screw = 40mm Co-efficient of friction of the screw thread = 0.15 Efficiency of the motor = 85% Determine the power required and efficiency of the screw
A leather faced cone clutch transmits power at 500 rpm. The semi-coneangle a is 12.5°. The mean diameter of the clutch is 300 mm, while the facewidth of the contacting surface of the friction lining is 100 mm. The coefficientof friction is 0.2 and the maximum intensity of pressure is limited to 0.07N/mm2. Calculate the force to engage the clutch and the power transmittingcapacity.
A 6-in-wide polyamide F-1 flat belt is used to connect a 4-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 3. The center-to-center distance is 8 ft. The angular speed of the small pulley is 1850 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, F1a, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.
The larger diameter and face of the disk of a multiple disk chutch are 225 mm and 20 mm respectively. The load applied to the spring of the clutch axially is 1500 N. Assuming that there are 8 pairs of friction 0.18 and tuning 800 rpm. Find the power transmitted by the clutch using uniform pressure method. (Ans, 13.67 kW)