A coarse sand sample 17 cm high and has a radiusIt is placed in a constant head ofcm and after 10 seconds, 49 g of water hasofof 2.27cm.45beencollected.Whatisthecoefficientpermeability of the sand?pts)

Answered: Image /qna-images/answer/c9a392e5-f341-470b-a461-7e026f2db243.jpg

A coarse sand sample 17 cm high and has a radius of 2.27 cm. It is placed in a constant head of of water has coefficient 45 cm and after 10 seconds, 49 been collected. What is the of permeability of the sand? pts)

A coarse sand sample 17 cm high and has a radius of 2.27 cm. It is placed in a constant head of of water has coefficient 45 cm and after 10 seconds, 49 been collected. What is the of permeability of the sand? pts)

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter11: Compressibility Of Soil

Section: Chapter Questions

Problem 11.14P

See similar textbooks

Related questions

Q: Diameter. 45 m STORE 12 m Liquid: 9.6 kN / m² YASS Internal friction angle: 35° Unit volume weight…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: For a sand with 4% finer than No. 200 sieve, estimate the maximum relative density ofcompaction that…

A: Given data: percentage finer =4% D50 = 1.4mm Assume; Compaction energy for the modified proctor…

Q: A mud sample containing 40lbm/bbl clay has a dial-reading value of 30 cp (at 600 rpm). Calculate the…

A: A plastic viscosity (PV) of the drilling fluid is calculated by subtracting the 300-rpm shear stress…

Q: For constant head laboratory test on fine sand, the following values are obtained. Length of…

A: we knowk=QLAhtQ=0.044in3L=10inA=π42.52h=22int=2minso,k=0.044in310inπ42.52×22in×2mink=0.002037inmin

Q: A sample of 500 g dry sand, when poured into a 2-litre capacity cylinder which is partially filled…

A: Given data : Mass of solid (M)=500 gVolume of solid (V)=188 cm3Density of water (ρWater )=1 g/cm3

Q: For a constant laboratory permeability test on a fine sand, the following data are given: Length of…

A: Given: Length of specimen Diameter of specimen Constant head difference Volume of water Time Void…

Q: The results of a constant head permeability test for a fine sand are as follows: Diameter of the…

A: solution For constant head permeability dia of sample d=33cm Area=π4d2=π4×332=855.3cm2Length of the…

Q: constant head permeability test was carried out on a sample of sand. The diameter and the length of…

A: We have formula for constant head test asQ=KiAVt=KhLAV=volumet=timeK=Hydraulic…

Q: A sample of 500 g dry sand, when poured into a 2 litre capacity cylinder which is partially filled…

Q: The result of a constant head permeability test for a fine soil sample having a diameter of 150mm…

Q: For a falling laboratory permeability test on a fine sand, the following data are given: Length of…

A: Given data: Length of specimen = 10 cm.Diameter of specimen = 9.5 cm.Diameter of standpipe = 1.5…

Q: For a constant head laboratory permeability test on a fine sand, the following are given: Length of…

Q: Question attached

A: Calculating the friction angle at different depth :

Q: of constant head permeability test for sand sample having a diameter of 100 mm and a length of 200…

A: Find coefficient of permeability for the soil,K=?

Q: The results of a constant head permeability test for a fine sand are as follows: Diameter of the…

Q: A sample of sand, 5 cm in diameter and 15 cm long, was prepared at a porosity of 60% in a…

A: Diameter = d = 5cm Length = L = 15cm ∆H = 30cm V = 40cm3 t = 5sec

Q: Refer to the constant-head permeability test arrangement in a two-layered soil as shown in Figure…

A: Given data: h1= 200 mm h2 =80 mm k1=0.004 cm/sec, H1 = 100 mm H2 = 150 mm. It is asked to…

Q: A clean quartzic sand (Gs = 2.69) has a dry unit weight of 14 kN/m³ at a moisture content of 7%. A…

Q: A rock sample has a length of 20.32 cm and a diameter of 5 cm. The pressure profile inside the core…

Q: Determine the coefficient of permeability, in cm/s, from the following data Length of sand sample…

Q: The coefficient of permeability of fine sand is 0.012 cm/sec at a voids ratio o0.57. Estimate the…

A: Please refer the attached image for complete solution.

Q: 16. For a constant laboratory permeability test on a fine sand, the following data are given:…

A: Length of specimen, L=16cmDiameter of specimen, D=97mm=9.7cmConstant head difference, h=51cmVolume…

Q: A sample of coarse sand is tested in a constant head permeameter. The sample is 20 cm. high and has…

A: Data given, Mass of discharge water = 1200gm Therefore, Volume of discharge water = 1200cc t = 15min…

Q: For a sand deposit where field testing indicates that the in-situ, e=0.50, D10=0.55mm and Cu=8.…

Q: A constant head permeability test is carried out on a cylindrical sample of sand 10 cm diameter and…

Q: Prob. A falling head permeability test was performed on a sample of silty sand. The time required…

Q: 7 3. A constant-head test was conducted on a sample of soil 10 cm long and 50 cm2 in cross-sectional…

A: Given data in question Constant head method Area Length of soil sample Volume collected Time taken…

Q: A cylindrical soil sample 50 mm in diameter and 200 mm in height is used as the permeameter in a…

Q: A falling head permeability test was carried out on a 15 cm long sample of silty clay. The diameter…

Q: A constant-head test was conducted on a sample of soil 15 cm long and 60 cm^2 in cross-sectional…

Q: The given values are as follows: The specimen's e=0.46 length of soil specimen=450mm constant…

A: The given data is: Void ratio of specimen (e) = 0.46 Length of soil specimen (L) = 450 mm = 0.45 m…

Q: The results of a constant head permeability test for a fine sand are as follows: Diameter of the…

Q: falling head permeability test

A: This is Soil Mechanics Problem. According to this problem , Falling head permeability test performed…

Q: For a constant head laboratory permeability test on a fine sand, the following are given: Length of…

A: ischrge velocity is given byQ=kiAv=kisov=QAi=headlengthi=450mm250mm

Q: A SAMPLE OF DRY SAND HAVING UNIT WEIGHT OF 16.50kN/m3 AND A SPECIFIC GRAVITY OF 2.70 IS PLACED IN…

A: step 1-

Q: The results of a constant head permeability test for a fine sand are as follows: Diameter of the…

Q: when a sample of medium sand was tested in a constant head permeameter, if the cross-section area of…

A: Given data: Cross-section=100 cm2 i=10 Q=10 cc/sec It is required to find the coefficient of…

Q: If the height of moist fine sand in a measuring cylinder is 10.5 cm and the height reduces when it…

A: given initial height of sand h1=10.5 cmreduced height of sand h2=8.2 cm

Q: The hydraulic conductivity of a sand at a void ratio of 0.85 is 0.08 cm/sec. Estimate its hydraulic…

Q: 5. In a constant-head permeability test, the length of the specimen is 200 mm and the cross…

A: Given data : Coefficient of permeability (K)=2.1×10-2 cm/secRate of flow (q)=130 cm3/minLength of…

Q: The results of a constant head permeability test for a fine sand are as follows: Diameter of the…

A: Given data of constant head permeability test Diameter of the sample (Ds) = 47 cm Length of sample…

Q: A 50 mm diameter and 90 mm-long silty clay sample was subjected to a falling head permeameter test…

A: Solution:- We know that in falling head permeameter test the permeability is given as:…

Q: PROBLEM 2: During a constant-head permeability test on a sand sample, 260 x 10° mm of water were…

Q: A wet sand sample has a volume of 4.55x10^-4 m^3 and weighs 8.4 N. After oven-drying, the weight…

Q: Prob. In a constant head permeability test following results observed - Distance between piezometer…

A: Given data, Distance between piezometer tappings, L = 100mm = 10cm Difference of water levels in…

Q: For a constant head laboratory permeability test on a fine sand, the following are given: Length of…

Q: A sample of sand is subjected to a constant head permeability test. The sample diameter is 60 mm and…

A: Given data Diameter of sample (D) = 60 mm Length of sample (L) = 130 mm Applied head (h) = 60 cm…

Q: Graduated flask Porous stone Soil specimen

Q: A cylindrical specimen of dry sand with a minimum and maximum void ratio (emin and emax) of 0.5 and…

A: We have relationRelative density isRd=emax-eemax-emin

Concept explainers

Weight-Volume relationships

Weight is defined as the quantity of matter contained in a body. Weight can also be defined as the force acting on a body due to gravity. Mathematically, weight can be defined as-

Question

A coarse sand sample 17 cm high and has a radius
It is placed in a constant head of
cm and after 10 seconds, 49 g of water has
of
of 2.27
cm.
45
been
collected.
What
is
the
coefficient
permeability of the sand?
pts)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water flows at the rate of 0.09 ml/s in an upward direction through a sand sample with a coefficient of permeability of 2.7 × 10^–2 mm/s. The thickness of the sample is 120mm and the area of cross-section is 5400 mm2. Taking the saturated unit weight of the sand as 18.9 kN/m3, determine the effective pressure in Pa at the middle of the sample. a. 364 b. 910 c. 182 d. 728
Water flows at the rate of 0.09 ml/s in an upward direction through a sand sample with a coefficient of permeability of 2.7 × 10^–2 mm/s. The thickness of the sample is 120 mm and the area of cross-section is 5400 mm2. Taking the saturated unit weight of the sand as 18.9 kN/m3, determine the effective pressure in Pa at the bottom of the sample. a. 364 b. 728 c. 182 d. 910
For a sand, given:D85 = 0.21 mmD50 = 0.13 mmD15 = 0.09 mmUniformity coefficient, Cu = 2.1Void ratio, e = 0.68Relative density = 53%Estimate the soil friction angle usinga. Eq. (2.87)b. Eq. (2.88)
Refer to Problem 3.5. Using Eq. (3.22), determine the averagerelative density of the sand.
In a deposit of normally consolidated dry sand a cone penetration test was conducted. Following are the result: Depth(m) Point resistance of cone, qc (MN/m²) 1.5 2.06 3.0 4.23 4.5 6.01 6.0 8.18 7.5 9.97 9.0 12.42 Assuming the dry unit weight of sand to be 16kN/m³, estimale the average peak friction angle, ф’, fo the sand. Use ф’=tan ¯1((0.38+0.27log(qc/ σ’o))
The following data are given for normally consolidated clay: Thickness=2.6m Primary Cc=0.3 Secondary Cc=0.02 e=0.8 Average Pressure=127 kPa Change in pressure (vertical) =46 kPa Determine the following 1. Primary Consolidation Settlement (Ans. 58.17mm) 2. Secondary Settlement five years after the completion of the primary settlement. The time for completion of primary settlement is 1.5 years. (Ans. 15.4mm)
8. The maximum and minimum dry specific weights of a given type of sand in the laboratory they are 17.8 and 14.6 kN/mª, respectively. How compact is the field if the relative compactness is 72%?
Refer to Problem 3.4. Using Eq. (3.22), determine the average relative density of sand.
A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7.89cm radius?
Q9) The results of a constant head permeability test for a fine sand are as follows: Diameter of the sample = 31 cm Length of sample = 98 cm Constant head difference = 52 cm Time of collection = 364 secs Weight of water collected = 448 grams Find the seepage velocity in cm/min. if the void ratio is 0.33. Round off to four decimal places.
Soil borings made at a site indicate that the top 8 m is a loose sand, with the groundwater table at 4 m below the ground surface. Below this is a fairly soft blue-gray silty clay with an average water content of 30%. The boring was terminated at 20 m below the ground surface when fairly stiff silty clay was encountered. For the upper sand gammadry = 14.0 kN/m3 and gammasat = 15.0 kN/m3 , where gamma is the unit weight. For the clay, ps = 2.70 Mg/m3 where p is density. (1) Calculate the total stress, pore water pressure, and effective stress at 0 (the surface), 4, 8, 14, 16, and 20 m below the ground surface. (2) Plot the soil profile and the variation of total stress, pore water pressure, and effective stress with depth.
In a constant head test, the sample of sand was collected 150 cm3 of water in just two minutes. The diameter is 5.08 centimeters, the length was 10 centimeters, and the head was maintained at 20 cm. 1) Determine the coefficient of permeability (Ans. 3.08 x 10-2 cm/s) 2) Determine the kind of soil (Ans. Coarse Sand) 3) Determine the interstitial velocity if n=0.3 (Ans. 0.21 cm/s)