A common emitter BJT circuit is designed as shown in Fig. 4(a). The output load line and defined Q-point of the circuit are shown in Fig. Determine the required values of Vcc, Rc and RB. Assume that VBE (on)=0.7 .V Vcc 12 c(mA) 10 RC - Ig3 = 30 µA 8 @point RB - I92 = 20 µA VCE 4 - Ig1 = 10 µA VBE Ves Veæ(V) = 10 V 5 10 15 20 25 إجابتك

A common emitter BJT circuit is designed as shown in Fig. 4(a). The output load line and defined Q-point of the circuit are shown in Fig. Determine the required values of Vcc, Rc and RB. Assume that VBE (on)=0.7 .V Vcc 12 c(mA) 10 RC - Ig3 = 30 µA 8 @point RB - I92 = 20 µA VCE 4 - Ig1 = 10 µA VBE Ves Veæ(V) = 10 V 5 10 15 20 25 إجابتك

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a four-resistor bias network for an npntransistor to give IC = 1 mA, VC E = 5 V, andVE = 3 V if VCC = 12 V and βF = 100. (b) Replaceyour exact values with the nearest values from theresistor and find the resultingQ-point
ı just need fınal answer Considering the dc operating conditions of the NMOS circuit in the figure, gm = 1.5 mS was obtained. Also, the load current IL flowing through RL when Rsig1 = 2 kΩ, Rsig2 = 3 kΩ, RF = 60 kΩ, R1 = 50 MΩ, R2 = 12 MΩ, RD = 4.7 kΩ, RS = 1.2 kΩ and RL = 13.3 kΩ What would be the value of ? (Vi1 = 20 mV, Vi2 = 30 mV) NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: The NMOS output impedance will be taken into account and its value is rd = 20 kΩ. a. 0,28 mA b. 0,20 mA c. 0,84 mA d. 0,40 mA e. 0,52 mA f. 0,72 mA g. 0,60 mA h. 0,12 mA
For many years, MOS devices were scaled tosmaller and smaller dimensions without changingthe power supply voltage. Suppose that the widthW, length L, and oxide thickness Tox of a MOS transistor are all reduced by a factor of 2. Assume thatVT N , vGS, and vDS remain the same. (a) Calculatethe ratio of the drain current of the scaled device tothat of the original device. (b) By what factor hasthe power dissipation changed? (c) By what factorhas the value of the total gate capacitance changed?(d) By what factor has the circuit delay Tchanged?
NPN BJTs can be used as emitter followers. In the given circuit, the emitter follower is connected to a non-ideal voltage source (Vs) with a source resistance (Rs). Beta is 100, Vce,sat is 0V, and Vbe is 0.7V. 1. What is Vo if Vs = 3V and Rs = 5k ohms? 2. What is Vo if Vs = 3V and Rs = 0 ohms?
For the circuit shown in Fig. 3, determine the values of R1 and R2 that make that id = 3.6 m, if both transistors have k = 0.4 mili-ampers by volts to square, and vt = 0.5 volts. (It is known that the DC source delivers 4 mA.)
Design a self-bias network using a JFET transistor with IDSS = 8 mA and VGS(off) =-6V to have a Q-point at IDQ =3,5 mA using a supply of 14 V. Assume that RD=3RS.A simple circuit may do. Thank you!
3) If IDSS = 8 mA and VP = - 6 V in the circuit with JFET transistors given below, calculate the current and voltage values of ID , VDS , VGS, VS, VDG and VD. (R1 = 910 KΩ, R2 = 220 KΩ, RD = 2.2KΩ, Rss = 1.2 KΩ, VDD = 18 V)
Design a self–bias network using a JFET transistor with IDSS = 8 mA and VP = –6V to have a Q-point at IDQ = 4 mA using a supply of 14 V. Assume that RD = 3RS and use standard values of the resistor. Show the details of your work and sketch the self–bias network with the standard value of RG, RD, and RS.
(a) An n-channel MOSFET has a mobility of 600 cm2/V · s and a channel length of 1 μm. What is the transistor’s fT if VGS − VT N = 0.25 V. (b) Repeat for a PMOS device with a mobility of 250 cm2/V · s. (c) Repeat for transistors in a new technology with L = 0.1 μm. (d) Repeat for transistors in a technology with L = 25 nm.
Considering the dc operating conditions of the NMOS circuit in the figure, gm = 4.1 mS was obtained. Also, the load current IL flowing through RL when Rsig1 = 2 kΩ, Rsig2 = 3 kΩ, RF = 60 kΩ, R1 = 50 MΩ, R2 = 12 MΩ, RD = 4.7 kΩ, RS = 1.2 kΩ and RL = 10.2 kΩ What would be the value of ? (Vi1 = 20 mV, Vi2 = 30 mV) NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: The NMOS output impedance will be taken into account and its value is rd = 20 kΩ.
Considering the dc operating conditions of the NMOS circuit in the figure, gm = 4.1 mS was obtained. Also, the load current IL flowing through RL when Rsig1 = 2 kΩ, Rsig2 = 3 kΩ, RF = 60 kΩ, R1 = 50 MΩ, R2 = 12 MΩ, RD = 4.7 kΩ, RS = 1.2 kΩ and RL = 10.2 kΩ What would be the value of ? (Vi1 = 20 mV, Vi2 = 30 mV) NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: The NMOS output impedance will be taken into account and its value is rd = 20 kΩ. a. 1,34 mA b. 0,40 mA c. 1,74 mA d. 0,94 mA e. 0,67 mA f. 2,01 mA g. 2,81 mA h. 2,41 mA
Consider an NMOS transistor fabricated in a 0.18-μm process with L = 0.18 μm and W = 2 μm.The process technology is specified to have Cox = 8 fF/μm2, μn = 450 cm2/V.s and Vtn= 0.55V.(a) Find VGS and VDS that result in the MOSFET operating at the edge of saturation with ID =(100+X) μA. Where X=Last digit of your ID+2.5. here x=2