A common source amplifier is given in Figure 12. The JFET has the following parameters: Ipss = 15 mA and VGs(off) = - 6 V. Propose suitable values for Rp and Rs if the amplifier circuit has voltage gain of 10 and VGs =VGs(off): [Suatu penguat sumber sepunya diberikan dalam Rajah 12. JFET tersebut mempunyai parameter-parameter tersebut: Ipss = 15 mA dan Ves(of) =- 6V. Cadangkan nilai-nilai yang sesuai untuk Rp dan Rs jika litar penguat tersebut mempunyai gandaan voltan 10 dan Ves =Ves(off)-] %3D

A common source amplifier is given in Figure 12. The JFET has the following parameters: Ipss = 15 mA and VGs(off) = - 6 V. Propose suitable values for Rp and Rs if the amplifier circuit has voltage gain of 10 and VGs =VGs(off): [Suatu penguat sumber sepunya diberikan dalam Rajah 12. JFET tersebut mempunyai parameter-parameter tersebut: Ipss = 15 mA dan Ves(of) =- 6V. Cadangkan nilai-nilai yang sesuai untuk Rp dan Rs jika litar penguat tersebut mempunyai gandaan voltan 10 dan Ves =Ves(off)-] %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A group of UTAS-Nizwa students are working on a project entitled "Gas leak detector alarm" for their final year in Diploma level. The circuit works on DC voltage of 16 volts and DC current of 7 milliampere. Students need to design a power supply circuit for their project. Consider an RMS voltage input of 220 volt, 60 Hz. Using a Full Wave Bridge Rectifier with Transformer, Silicon diode and Capacitor Filter, Design the power supply. a. Compute for the load resistance, peak output voltage, input peak voltage to the diodes (secondary voltage), peak input voltage and the turns ratio of the transformer. 1. What is the value of the load resistance? b. Draw the Power Supply circuit (capacitor filter connected in parallel with the resistor) and write the computed values (No value for the capacitor).
Trying to solve this MOSFET question but not sure how.(Given Answer:a) Av = -gm (ro|| RD)b)Av = -30.7 Ri = 20 kohm Ro = 7.67 kohm)
COURSE: INDUSTRIAL ELECTRONICS DEGREE: BS ELECTRICAL ENGINEERING For a unijunction transistor with VBB = 20V, n = 0.65, RB1 ✓ 2K-ohms (IE = 0), and VD = 0.7, determine: a) RB2 b) RBB c) VRB1 d) VP
1. Which of the following is a type of error associated with digital-to-analog converters (DACs)? A. nonmonotonic error B. incorrect output codes C. offset error D. nonmonotonic and offset error 2. A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 0101. A. 0.3125 V B. 3.125 V C. 0.78125 V D. –3.125 V 3. A binary-weighted digital-to-analog converter has an input resistor of 100 k. If the resistor is connected to a 5 V source, the current through the resistor is: A. 50 A B. 5 mA C. 500 µA D. 50 mA 4. What is the resolution of a digital-to-analog converter (DAC)? A. It is the comparison between the actual output of the converter and its expected output. B. It is the deviation between the ideal straight-line output and the actual output of the converter. C. It is the smallest analog output change that can occur as a result of an increment in the digital input. D. It is its ability to resolve between…
Consider a two 14 V or 16 PV modules that may be connected in series or parallel at the input of a single phase dc-to-ac converter. This converter is used to supply ac power to a 60-watts heating (resistive) load of 2.4 Ω. The on-state voltage drop of the switching transistor is 2 V. Select suitable dc-to-ac converter having low conversion losses. You may assume any appropriate switching frequency and ignore the other switching parameters (delay time, rise time, fall time, storage time and leakage current).
2.1 A regulator has a no-load output voltage of 12 V and a full-load output of 11.9 V at a load current of 140 mA. Determine the voltage regulation as a percentage change from no-load to full-load and also as a percentage change for each mA change in load current. (6)2.2 What are three types of switching regulators? (3)
From the following three-wire circuit let Van = Vnb = 120 ∟0° Vrms, determine: a.) InN b.) The active power delivered by each source
Table 1: Oscillator circuit parameters and circuit componentsC2 = 5100 pF; Amplifier gain = 11; Select R1/R2 = C2/C1, f = 20 kHzNote: The circuit is to be designed with an ac bridge that balances only at a particular supply frequency. 1.From Table 1, determine R3 in terms of R4:2.From Table 1, determine R1 in terms of R2:3.From Table 1, determine C2 in terms of C1:
application of bias circuits of the BJT in AC a. determine Zi and Zo b. Calculate Av and Ai c. repeat literal (a) with ro = 20k ohm d. repeat literal (b) with ro = 20k ohm
design monostable multivibrator,astable mutivibbrator, bistable multivibrator using multisim by using 555 timer IC,tiemperiod. and also by using transistor?
1. The collector-base voltage of a Si transistor is a. None of these b. zero c. 0.7 volts d. 0.3 volts 2. The current gain of a common-emitter transistor is the ratio of the a. base current to collector current b. collector current to emitter current c. collector current to base current d. Emitter current to collector current 3. A zener diode shunt regulator uses the zener connected a. in series with the load b. in series with RS c. across RS d. across the load 4. If the transistor is to operate in the saturation region, the base-emitter and the base-collector terminal has to bea. both forward-biased b. both reversed-biased c. reversed-biased and forward-biased respectively d. forward-biased and reversed-biased respectively 5. The base-emitter of the transistor operating in the active region is usually a. operating in the breakdown region b. reverse-biased c. forward-biased d. non-conducting
A 565 IC PLL has an external resistor R1 of 1.2 kΩ and a capacitor C1 of 560 pF. The power supply is 10 V. (a) What is the free-running frequency? (b) What is the total lock range?