A compaction test has been conducted and measurements of bulk unit weight, Obulk, and moisture content have been obtained as shown in the Table below. Determine the maximum dry density and optimum moisture content. Ybulk moisture content (g/cm³) (%) 1.23 15.71 1.31 16.37 1.46 19.09 1.44 21.19 1.42 23.23

A compaction test has been conducted and measurements of bulk unit weight, Obulk, and moisture content have been obtained as shown in the Table below. Determine the maximum dry density and optimum moisture content. Ybulk moisture content (g/cm³) (%) 1.23 15.71 1.31 16.37 1.46 19.09 1.44 21.19 1.42 23.23

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter34: Miscellaneous Separation Methods

Section: Chapter Questions

Problem 34.14QAP

See similar textbooks

Similar questions

Question: For particles having a size range of 1.27 x 10^2 mm to 5.08 x 10^-2 mm. Calculate the size range of the various fractions obtained using free settling conditions. Also calculate the value of the largest Reynolds number occuring.
What are the physical states of dispersed phase and dispersion medium in foam rubber.
An Ostwald viscometer was used to determine the time of flow of syrup at 20 °C. Data for Water:Time of flow: 0.23 secondsDensity at 20 °C: 0.998 g/cm³Viscosity: 0.0101 poiseData for Syrup:Time of flow: 1.42 secondsDensity at 20 °C: 1.153 g/cm³ Input all numerical answers to the 3rd decimal place 1. What is the viscosity of syrup? * 2. From the computed viscosity of syrup, what will be its fluidity? 3. What is the kinematic viscosity of water? 4. From the computed viscosity of syrup, what will be its kinematic viscosity? 5. What is the fluidity of water?
Determine whether the first part of statement will INCREASE, DECREASE or have NO EFFECT in the second part of the statement. 1. If there is an increase in the number of Frenkel Defects then the overall charge will _____. 2. If there is a decrease in molecular weight then the melt viscosity will ____. 3. If there is a decrease between Mw and Mn then the dispersity will ______.
The viscosity of Ethyl acetate determined at 25°C was 4.2cp. The efflux time for water to flow from marks A to B was 3 minutes.Additional data: Viscosity of water at 25°C = 1.002cp Density of water at 25°C = 0.997g/mL Calculate for the time for a 10.0mL Ethyl acetate (equivalent to 5.0g) to flow from Marks A to B.
For a face center cubic crystal, where the applied load is in the [1 0 0] direction, assume the ABC is the slip plane where A[1 0 0], B [0 0 1] and C [0.1, 1 0] 1. Find the normal vector to the above slip plane. 2. Find the angle phi, between the normal to the slip plane and the applied load direction. 3. Find the angle Lamda between applied load and slip direction, assume slip direction is the direction BA
Which organic liquid has: Molecular weight = 79.53g/mol Density = 0.7708 g/ml Viscosity = 1.39 mPa.s index of refraction = 1.420
According to Riippi et al. (1998), briefly discuss the effects of increased compression force to the following tablet properties: Disintegration time Surface profiles (as seen on SEM photographs)
Source of error in viscosity for glycerin liquid.
A polystyrene component must not fail when a tensile stress of 1.25 MPa (180 psi) is applied. Determine the maximum allowable surface crack length if the surface energy of polystyrene is 0.50 J/m^2 (2.86 10^-3 in.-lbf/in^2). Assume a modulus of elasticity of 3.0 GPa (0.435 10^6 psi).
Which of the following are safe and effective techniques for drying organic solids recovered from a filtration? (Choose all that apply). a. Spreading the solid evenly on a watch glass or aluminum weigh boat and placing it in an oven set at a temperature 20 °C below the substance's expected melting point. b. Placing it on top of a hotplate set on low. c. Leaving the solid on the funnel with the vacuum on for several minutes. d. Blowing on the solid.
In simple words, describe the following steps in fabricating an IC: a- Crystal growth; b- Epitaxial layer growth; c- Oxidation d- Photo-masking, Photolithography and Photo etching e- Diffusion: Isolation diffusion; Base diffusion; and Emitter diffusion. f- Metallization & interconnections; g- Scribing & Mounting and h- Packaging and Quality Control.