A composite bar is fabricated by brazing aluminum alloy [E = 10,000 ksi] bars (1) to a center brass [E = 17,000 ksi] bar (2) as shown in the figure. Assume d = 0.75 in., a = 0.2105 in., L = 21 in. If the total axial force carried by the two aluminum bars must equal the axial force carried by the brass bar, calculate the thickness b required for brass bar (2).

A composite bar is fabricated by brazing aluminum alloy [E = 10,000 ksi] bars (1) to a center brass [E = 17,000 ksi] bar (2) as shown in the figure. Assume d = 0.75 in., a = 0.2105 in., L = 21 in. If the total axial force carried by the two aluminum bars must equal the axial force carried by the brass bar, calculate the thickness b required for brass bar (2).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.4P

See similar textbooks

Similar questions

Derive an expression for the critical thickness of insulation of cylindrical pipe. Explain in detail.
PROBLEM: VA-17 FROM THE BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD.
Using information acquired from the National Transportation Safety Board (NTSB), explain the role that epoxy creep played in the 2006 collapse of a 3-ton concrete ceiling panel in Boston’s Fort Point Channel Tunnel. What could have been done to prevent this disaster?
Calculate the young’s modulus from one of these two graphs?
In the following set of questions, we will consider a mercury-in-glass thermometer. The tworeference points will be assigned 0.01◦C and 100◦C based on the triple point and boiling point ofwater. a) Remark on the the rationale for selecting references based on phenomena such as phase transi-tions. Identify any prospective issues or special considerations one might have with this approach? b) Draw a schematic of a mercury-in-glass thermometer. Define an appropriate set of universe,system, and surroundings and explain the functional operation of thermometer from a thermody-namic analysis perspective. In your response, you should describe how energy flows and influencesmatter. Is your system open or closed? What kind of boundary do you have? What kind ofapproximations (if any) do you make for the reliable determination of temperature based on yourdecomposition of universe, system, and environment?
PROBLEM:VIC-13 FROM THE BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD.
. Estimate the heat-transfer rate per foot of length from a 0.02-in. diameter nichrome wire immersed in water at 240F. The wire temperature is 2200F. 2. Two thousand watts of electrical energy are to be dissipated through copper plates measuring 5 cm by 10 cm by 0.6 cm immersed in water at 390 K. How many plates would you recommend? Substantiate all of the design criteria used.
Calculate a thermal resistance of a copper tube (d1 = 0.192 mm, d2 = 0.208 mm, λ = 310 W/mK) with a Styrofoam layer of di = 0.070 mm.
Q1. Well water contained in an AISI 304 SS pipe network for chemical treatment and posterior distribution by aerial water pipes to different locations in a food manufacturing facility was analysed. The AISI 304 SS pipe network had an approximate 300 m length, 154 mm diameter and 2.0 mm wall thickness. The AISI 304 SS pipes were welded using a Tungsten Inert Gas (TIG) welding procedure. In-situ weld quality assurance was tested by pressurized WW, and no pinhole leakage was detected. After the pipe network remained out of service for 6 months at room temperature containing stagnant, pressurized well water, pitting corrosion was observed on the weld joints and the base material by the presence of multiple pinhole leaks.(a) Discuss, with chemical equations if relevant, TWO corrosion events that may have caused the pitting corrosion.(b) What practical steps could have been taken to mitigate for this potential outcome?(c) Identify corrosion inhibition methods to mitigate for the corrosion…
How Johnson's equation of column differs from the Euler's equation? Explain briefly.
What is the stress concentration factor for a part under axial load with a shoulder fillet if d=1.5", D=2.5" and r=.15" (please state which table you used please)
What is the shape factor F12 for the situation shown in Fig. 1 below ?