In figure raws a on ol a 2. In the system storage tank through a pipe with cross sectional area 0.05ft². The velocity in the suction line is 3 ft/s (0.914 m/s). The pump discharges through a pipe with cross sectional area 0.02 ft² to an overhead tank. The end of the discharge pipe is 50 ft (15.2 m) above the level of the solution in the feed tank. Friction losses in the entire piping system are 10 ft. lbf/lb (29.9 J/Kg). What is the work done by the pump per unit mass of water? (25%) 1 A = 0.02 50 ft A = 0.05ft² Pump 2 ft² a b

In figure raws a on ol a 2. In the system storage tank through a pipe with cross sectional area 0.05ft². The velocity in the suction line is 3 ft/s (0.914 m/s). The pump discharges through a pipe with cross sectional area 0.02 ft² to an overhead tank. The end of the discharge pipe is 50 ft (15.2 m) above the level of the solution in the feed tank. Friction losses in the entire piping system are 10 ft. lbf/lb (29.9 J/Kg). What is the work done by the pump per unit mass of water? (25%) 1 A = 0.02 50 ft A = 0.05ft² Pump 2 ft² a b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.235 m and the pipe lengths are L1= 5 m, L2= 4.5 m, L3= 1.5 m, and L4= 0.6 m. The impeller of the centrifugal pump has a diameter of 0.55 m and operates at 850 rpm. The uniform blade height is 51 mm. The water enters the pump parallel to the pump shaft with a flow rate of 0.16 m3/s. Take viscosity as 0.00112 N s/m2. Fig Q2: Piping system to pump water between two tanks. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3. a) What would be the shaft power required to turn the impeller if the exit blade angle is 31 degrees. b) Find the major losses in the system. Take the pipe Darcy friction factor as 0.055. c) Determine the difference in height between the water surfaces in the two tanks assuming that there are no losses within the pump.
The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.235 m and the pipe lengths are L1= 5 m, L2= 4.5 m, L3= 1.5 m, and L4= 0.6 m. The impeller of the centrifugal pump has a diameter of 0.55 m and operates at 850 rpm. The uniform blade height is 51 mm. The water enters the pump parallel to the pump shaft with a flow rate of 0.16 m3/s. Take viscosity as 0.00112 N s/m2. Fig Q2: Piping system to pump water between two tanks. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3. a) What would be the shaft power required to turn the impeller if the exit blade angle is 31 degrees. b)
1. The figure shows a pump that draws 840 L/min of crude oil (s= 0.85) in an underground storage drum to the first stage of a processing system; a) If the total energy loss in the system is 4.2 N m/N of oil flow, determine the power transmitted by the pump to the fluid. b) If the energy loss in the steel suction line is 1.4 N m/N of oil flow, determine the pressure at the pump inlet
The outer diameter of an impeller of a centrifugal pump is 300mm and outlet width is 50mm. The pump is running at 800 rpm and is working against a total head of 20 m. The vanes angle at outlet is 40 deg and manometric efficiency is 75%. Determine: (a) velocity of flow at outlet; (b) velocity of water leaving the vane; (c) angle made by the absolute velocity at outlet with the direction of motion at outlet; and discharge.
2. Water from an open reservoir A at 8m elevation is drawn by a motor-driven pump to an open reservoir B at 70m elevation. The inside diameter of the suction pipe is 200mm and 150mm for the discharge pipe. The suction line has a loss of head three times that of the velocity head in the 200mm pipe. The discharge line has a loss of head 20 times that of the velocity head of the discharge pipeline. The pump centerline is at 4m. Overall efficiency of the system is 78%. For a discharge rate of 10 li/s, find the power input to the motor.
Assume that friction in the suction line is negligible. Toluene @ 35C is pumped from an open reservoir to a tank kept at a gauge pressure of 150 kPa. The pump itself is 3 m below the reservoir, while the discharge tank is 10m above the reservoir. While in the discharge line the friction head amounts to 7.5 m, determine the net positive suction head available for the pump. If the pump has an efficiency of 65%, determine the total power input. At the given temp, the density and vapor pressure of toluene are 862 kg/m3 and 40 mmHg.
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i. Determine Delta Z (Z2 - Z1) in ft. ii. What is the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s. iii. What is the mass flow rate of the water in lbm/s?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. answer the ff: i. Determine the velocity of the water at point 2. ii. Reynolds number for the flow. iii. A pump efficiency of 55% means that the theoretical work needed for the process is 55% of the actual work needed. In other words, 55% more shaft work is necessary. Determine the theoretical shaft work required in foot-pound force per pound mass.
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i.Let us set our first point at the surface of the large reservoir, and the second point at the surface of the open elevated tank. Determine the velocity of the water at point 1 in ft/s. ii.What is the density of water at the conditions stated in lb/ft3? iii.If 1 horsepower is equivalent to 500 (ft-lbf)/s, the pump should be able to supply how much hp?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. a. Assuming that the large open reservoir is open to the atmosphere as well, what is the mechanical energy balance eq for the system? b. What is the Reynolds number for the flow ?
A pump draws water from open reservoir A at 20 ft above pump centerline and lifts to an open reservoir B at 250 ft above pump centerline. The loss of head at the suction is 5 times the velocity head at the 6 inches suction pipe and at the discharge is 15 times the velocity head at the 4 inches discharge pipe. The pump discharge is 200 GPM. a. The total dynamic head in ft.
2. A pump draws water from a lake delivered to a height of 50 meters above the lake and encounters 15 meters of headloss. Determine the pump power requirement in Kilo-Watts to deliver a constant supply of 500 Liters per second? The correct answer has a margin of 1 from exact answer. Velocity head is neglected.