A compound shaft consists of segment (1), which has a diameter of 1.9 in., and segment (2), which has a diameter of 2.3 in. The shaft is subjected to a tensile axial load of P = 22 kips and torques TA= 8 kip-in. and Tg = 33 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. P A TA (1) H N TB B (2) K C

A compound shaft consists of segment (1), which has a diameter of 1.9 in., and segment (2), which has a diameter of 2.3 in. The shaft is subjected to a tensile axial load of P = 22 kips and torques TA= 8 kip-in. and Tg = 33 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. P A TA (1) H N TB B (2) K C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum absolute bending strain in the following tubular shaft if di = 160 mm and do = 200 mm. (E = 154 GPa)
For the shaft shown, a. Determine the maximum stress on the shaft and the maximum angle of twist of end D relative to end A. b. If the stress in every section must not exceed 25 MPa, what should be the uniform diameter of the shaft? dAB = 100mm, dbc = 80mm, dcd = 50mm G for the shaft is 80GPa. Consider clockwise torques as negative.
The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 4.0 ft, and c = 8.5 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
A torque of magnitude T = 1000 N-m is applied at D as shown. Shaft AB and CD have an elliptical cross-section. The major and minor diameters of shaft AB are 56 mm and 50 mm respectively, while the major and minor diameters of shaft CD are 42 mm and 38 mm respectively. Find the maximum shearing stress in shaft CD. Answer must be in MPa
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
A solid constant-diameter circular shaft is subjected to the torques of TA = 490 lb·ft, TB = 1080 lb·ft, TC = 830 lb·ft, and TD = 240 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7400 psi, what is the minimum acceptable diameter for the shaft?
A solid 1.750-in.-diameter steel shaft is subjected to torques TB = 285 lb-ft and TD= 115 lb-ft, acting in the directions shown. If the allowable shear stress in the shaft is 22 ksi, determine the maximum torque TC that can be applied to the shaft.
The solid steel shaft carries the torques T1= 1200 Nm and T2=750 N m. Using L1=L2=2.5 m and G = 83 GPa, determine: a. draw a diagram using a double headed arrows showing the torque in each segment b. determine the shear stresses in each segment and the angle of rotation of the free end if the diameter is 100 mm. c. the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 4^0.
Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading Pshown,a) Find reactions at A and B.b) Determine the normal and shearing stresses at Point K and Point H. α (˚) =30 P (kN)=14
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
Question-04: Solve for the torque T that can causes a maximum shearing stress of 4.2 ksi in the cylindrical steel shaft as shown in Figure 3. Assume radius of the shaft r = 1.2inches.