A concentration cell constructed from two hydrogen electrodes,both with PH2 = 1.00. One electrode is immersed inpure H2O and the other in 6.0 M hydrochloric acid. What isthe emf generated by the cell, and what is the identity of thean electrode that is immersed in hydrochloric acid? (a) -0.23 V, cathode(b) 0.46 V, anode(c) 0.023 V, anode(d) 0.23 V, cathode(e) 0.23 V, anode

Q: What is the electrical current, in Amperes, that must be applied if 6.50 g Ag is deposited at the…

A:

Q: How long will it take to plate out 3.9 g Ni from aqueous Ni2+ with a current of 108.2 A? HOW DO WE…

A: To plate Ni using the process of electrolysis, the reaction that needs to be employed on the…

Q: During a period of discharge of a lead–acid battery, 402 gof Pb from the anode is converted into…

A: Overall cell reaction is Pb(s) + PbO2(s) + 2H+ (aq) + 2HSO4- → 2 PbSO4 + 2H2O Where, 1 mol of Pb is…

Q: (a) Calculate the mass of Li formed by electrolysis of moltenLiCl by a current of 7.5 x 104 A…

A: (a) Given that a current of 7.5×104 A was flowed for a period of 24 h.

Q: Elemental calcium is produced by the electrolysis of moltenCaCl2. (a) What mass of calcium can be…

A: a.

Q: A concentration cell was set up at 343 K using two hydrogen electrodes. If the cell is generating a…

A: The concentration cell of hydrogen can be expressed as follows: Pt, H2 (g) I H+ (aq) [C1]  ∥  H+…

Q: To what pH should you adjust a standard hydrogen electrode toachieve an electrode potential of…

A:

Q: If the potential of a cell is 0.51 V at 25°C when [Zn2+(aq)]=0.111M and the pressure of the hydrogen…

A:

Q: What is the pH of the solution in the cathode half-cell when PH2 = 1.0 atm, 3Zn2+4 in the anode…

A: The anodic half-reaction and cathodic half-reaction that occurred in the electrochemical cell are as…

Q: A voltaic cell is constructed in which the cathode is a standard hydrogen electrode and the anode is…

A: The call reaction at anode is, H2(g) ------> 2H+(aq) + 2e- Standerd cell potential of the cell =…

Q: The passage of a current of 0.750 A for 25.0min deposited 0.369 g of copper from a CuSO4 solution.…

A:

Q: Given the balanced electrochemical reaction below (M and N represent generic metals), what is the…

A: The concentration of M3+ can be calculated by using Nerst equation. Nerst equation is given as…

Q: 6) Chromium can be electroplated from aqueous potassium dichromate, with the reduction shown below.…

A:

Q: During the discharge of an alkaline battery, 4.50 g of Znis consumed at the anode of the battery.…

A: Faraday's Law of Electrolysis: The Faraday's law of electrolysis states that the amount of electric…

Q: (a) Calculate the half-cell potential for the reaction O2(g) + 4 H3O* (aq) + 4 e¯ → 6 H;0(€) at pH 7…

A: Standard electrode potential is the “potential that is measured by taking SHE on the other side”.…

Q: How long would it take to deposit 9.38 g of copper (molar mass 63.55 g/mol) at the cathode of an…

A: Faraday's law states that the amount of chemical change that is produced by passing a current to an…

Q: Brass, an alloy of copper and zinc, can be produced by si-multaneously electroplating the two metals…

A:

Q: Question three on photo

A: question is based on Faraday's first law of electrolysis. i.e., amount of substance deposited is…

Q: Molten CaCl, can be electrolyzed to form metallic Ca. For what duration should an electrolysis be…

A:

Q: How long will it take to plate out 4.9 g Ni from aqueous Ni2+ with a current of 113.1 A?

A:

Q: What is the pH of the solution in the cathode half-cell inFigure when PH2 = 1.0 atm, [Zn2+] in the…

A: SOLUTION: Step 1: The anodic half-reaction and cathodic half-reaction that occurred in the…

Q: To construct the galvanic cell illustrated above, the salt bridge was prepared by soaking a piece of…

A: Answer = The correct option is (D) According to the question - Galvanic cell -  Galvanic cell is a…

Q: How long will it take to plate 2.5 g of copper onto a light fixture using a solution of Cu(NO3)2 and…

A:

Q: What volume of chlorine gas at standard temperature and pressure is evolved when a solution of MgCl2…

A: Provided time=1hour Molar mass of Cl2=70.906g/mol Let w gram Cl2 evolve So provided time…

Q: If the potential of a Zn-H+cell is 0.45V at 25 degrees C when[Zn]-1.0M and PH2=1.0 atm, what is the…

A:

Q: he table below gives the standard electrode potential values of some electrodes. A salt bridge is…

A: The electrochemical cells are made by connecting two electrodes of different potential. These cells…

Q: Determine the mass of Al2(SO4)3 required to prepare 0.01N solution in 100 ml volume. Compare the…

A:

Q: Chromium can be electroplated from aqueous potassium dichromate, with the reduction shown below. If…

A: Current = 5 A Voltage = 4.5 V Time = ? Volume = 215 mL = 0.215 L Molarity = 1.19 M

Q: At what pH will hydrogen electrode at 298 K show an electrode potential of-0.118 V, when Hydrogen…

A: The cell potential is usually measured in volts and is defined as the potential difference between…

Q: Enter your answer in the provided box. Consider the following electrochemical cell in, for which E"…

A:

Q: How many liters of O2 at 298 K and 1.00 bar are produced in 2.50 hr in an electrolytic cell…

A: According to Faraday’s first law, the chemical deposition which takes place during electrolysis is…

Q: How many liters of O2 at 298 K and 1.00 bar are produced in 2.75 hr in an electrolytic cell…

A: given: Pressure (P) = 1.00 bar temperature (T) = 298 K Time (t) = 2.75 hour x 3600 = 9900 sec…

Q: Determining molar mass by electrolysis. An electrolysis cell containing MSO4 solution is operated…

A:

Q: How many minutes would it take to plate 12g of silver from an aqueous Ag(l) solution using a current…

A:

Q: A steady current of 3 A is maintained for 10 mins in AgNO3 solution. How much Ag is deposited at the…

A: Given: Current is 3 A. Time is 10 minutes. To find: Mass of Ag on cathode

Q: 1.) A sodium sulfate solution was electrolyzed using inert Pt electrodes. The cathode reaction was…

A: As per our guidelines, we are supposed to answer only one question so kindly repost the other as…

Q: A Cu electrode is immersed in a solution that is 1.00 Min [Cu(NH3)4]2+ and 1.00 M in NH3. When the…

A: The process is : 2H+(aq)+Cu(s)+NH3(aq)→H2(g)+[Cu(NH3)4]2+ The Nernst equation is,…

Q: A galvanie cell is powered by the Re olox Regctiom: 3+ 2H,014)+4 fe Caa). writea balamced equation…

A: Interpretation - A balanced equation for the half reaction anode and cathode and the cell voltage…

Q: (a) A Cr* (aq) solution is electrolyzed, using a current of 7.60 A. What mass of Cr(s) is plated out…

A:

Q: A 0.1 M aqueous CaCl, solution is electrolyzed by usina inert electrodes. If 1.25 ampere current is…

A: At cathode this reaction is taking place,Ca2+  +  2e-   →  Ca  Calculate the charge first,Q = it and…

Q: 18. When pH = 7, p(O,) = 100 kPa, O, + 4H" + 4e calculate the electrode potential in according to…

A: 1 bar = 100 kPa [H+] = 10-pH = 10-7 M Nernst equation: EO2/H2O = EO2/H2O° -0.05914log1PO2×H+4…

Q: 6) Chromium can be electroplated from aqueous potassium dichromate, with the reduction shown below.…

A:

Q: Given the balanced electrochemical reaction below (M and N represent generic metals), what is the…

A: This problem is based on Nerst equation.

Q: 1. Consider a cell buffered at pH 2.00 and consists of Fe2+(aq) (0.004 M), Fe3+(aq) (0.070 M) and…

A: Redox reactions in electrochemistry are characterized as chemical processes in which electrons…

Q: An aqueous solution of an unknown salt of ruthenium is electrolyzed by a current of 3.00 A passing…

A: Given Current (I) = 3A Given mass = 1.572g Time = 25min = 1500s Molecular weight = 101.07g

Q: Molten CaCl, can be electrolyzed to form metallic Ca. For what duration should an electrolysis be…

A: Given: The amount of current passed through the solution for electrolysis is 1.44 A. The mass of Ca…

Electrolysis

Electrolysis is defined as the process of breaking down ionic compounds into their constituent elements by passing a direct electric current through the compound in a fluid state. The cathode reduces cations, while the anode oxidizes anions. An electrolyte, electrodes, and some form of external power source are the main components required for conducting electrolysis. A partition, such as an ion-exchange membrane or a salt bridge, may also be used, but this is optional. These are primarily used to prevent the products from diffusing near the opposing electrode.