A consolidated-drained triaxial test is carried out on a sand specimen that is subjected to 80 kN/m² confining pressure. The vertical deviator stress was increased slowly such that there is no built-up of pore water pressure within the specimen. The specimen failed when the addition axial stress reached 240 kN/m². Find the friction angle of the sand. If another identical sand specimen was subjected to 150 kN/m² confining pressure, what would be the deviator stress at failure.

A consolidated-drained triaxial test is carried out on a sand specimen that is subjected to 80 kN/m² confining pressure. The vertical deviator stress was increased slowly such that there is no built-up of pore water pressure within the specimen. The specimen failed when the addition axial stress reached 240 kN/m². Find the friction angle of the sand. If another identical sand specimen was subjected to 150 kN/m² confining pressure, what would be the deviator stress at failure.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter2: Geotechnical Properties Of Soil

Section: Chapter Questions

Problem 2.18P

See similar textbooks

Similar questions

A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure were determined to be 6100 psf and 4600 psf, respectively. a. Determine the angle of internal friction of the sand? b. Determine the angle of the failure plane? c. Determine the maximum principal stress? Please answer this asap. For upvote. Thank you very much
Friction angle of dry sand is 35°. In a direct shear test on this sand, a normal stress of 150kPa was applied. What shear stress will cause the failure? (a) 150kPa (b) 50kPa (c) 78kPa (d) 105kPa
A sand sample is subjected to direct shear testing. Two tests areperformed. For test 1, The sample shears at a stress of 2500 psf whenthe normal stress is 4000 psf.Test 2, The sample shears at a stress of 3500 psf when the normalstress is 6000 psf. Determine the following:a) Angle of Internal frictionb) Value of cohesionc) Compute the shear stress at a depth of 12 ft. if the unit weight ofthe soil is 150 pcf
After conducting a tri-axial test on a sand sample, the normal and shearing stress on the failure plane at failure was found to be 475kPa and 350kPa, respectively. Which of the following most nearly gives the plunger stress?
2. A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure was determined to be 6,300 psf and 4,200 psf, respectively. a. Determine the angle of internal friction of the sand. b. Determine the angle of failure plane. c. Determine the maximum principal stress.
A sample of dry sand is subjected to a tri- axial test. The angle of internal friction is 34.8°. The minor principal stress is 240 KPa. What is the major principal stress when the failure occurs in KPa?
4- In a consolidated-drained triaxial test on a clay, the specimen failed at a deviator stress of 2,590 lb/ft². If the effective stress friction angle is known to be 29°, what was the effective confining pressure at failure?
A sample of dry sand is subjected to a tri- axial test. The angle of internal friction is 36.6°. The minor principal stress is 192 KPa. Compute the effective normal stress in KPa at the point where shear occurs at the failure plane.
A sample of dry sand is subjected to a tri- axial test. The angle of internal friction is 37.6°. The minor principal stress is 231 KPa. What is the deviator stress when the failure occurs in KPa?
In a drained triaxial test carried out on a specimen of clean dry sand failure occurred when the total vertical stress was 423 kPa and lateral stress was 138 kPa. a) b) The value of o' of the sand, The normal and shear stress acting on the plane where failure is about to occur,
An undisturbed soil sample, 110 mm in diameter and 220 mm in height, was tested in atriaxial machine. The sample sheared under an additional axial load of 3.35 kN with avertical deformation of 21 mm. The failure plane was inclined at 50˚ to the horizontal and the cell pressure was 300 kN/m2. i. Draw the Mohr circle diagram representing the above stress conditions, and from it determine:− Coulomb’s equation for the shear strength of the soil, in terms of total stress;− the magnitude and obliquity of the resultant stress on the failure plane.
An undisturbed soil sample, 110 mm in diameter and 220 mm in height, was tested in a triaxial machine. The sample sheared under an additional axial load of 3.35 kN with a vertical deformation of 21 mm. The failure plane was inclined at 50˚ to the horizontal and the cell pressure was 300 kN/m2. i. Draw the Mohr circle diagram representing the above stress conditions, and from it determine: − Coulomb’s equation for the shear strength of the soil, in terms of total stress; − the magnitude and obliquity of the resultant stress on the failure plane