A control block costs $.75 per part to mill without a fixture and $.43 per part when a fixture is used. Assuming the cost of the fixture is $175.00, how much will the fixture save over a production run of 2200 parts?

A control block costs $.75 per part to mill without a fixture and $.43 per part when a fixture is used. Assuming the cost of the fixture is $175.00, how much will the fixture save over a production run of 2200 parts?

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter6: Milling

Section6.3: Vertical Milling Machine Operations

Problem 9RQ: When squaring a block on the vertical mill, what surface of the block should be machined first, and...

See similar textbooks

Related questions

Q: Calculate the spindle speed for a Lathe Machine, if the cutting speed for a mild steel material…

A: Cutting speed for mild steel, Vc=34 m/min Diameter of workpiece, d=46 mm=0.046 m

Q: (b):- Calculate the total time to mill a block of aluminum with dimensions of 100 x 40 x 50 to…

Q: Task : (Machining part) copy and draw the figure below, and describe the process of using CA6140…

A: Lathe machine A lathe machine is a machine tool that removes the undesired material from a rotating…

Q: 4. Explain the differences between the up milling and down milling?

Q: In a slab milling operation , L_w = 200 mm table feed = 18 mm/min, diameter of cutter = 34 mm depth…

A: Given Data: The length of the slab is, Lw=200 mm. The feed rate of the table is, f=18 mm/min. The…

Q: In 3-axis milling, the table feedrate is 756.00 mm/min. Using a 10mm endmill to cut the material…

Q: The length, width and thickness of a steel sample are 400 mm, 40 mm and 20 mm, respectively Its…

Q: In a turning operation, the operator has established that a single pass on the cylindrical workpiece…

A: Given data as per questionMachining time (Tm)=5 minLength of piece (L)=400mmdiameter of work piece…

Q: A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter.…

A: The processing time required is 30.61625 min.

Q: a) With a neat diagram briefly explain the principle of operation of Shaping machine. b) Write any…

A: Diagram of shaper machines Principle of shaper machines - it holds the workpiece on the table and…

Q: Estimate the time required to face mill a 10-inch long, 2-inch wide block of brass with a 6-inch…

A: Brass dimension is given:10 inch long2 inch wide6 inch diameter cutter

Q: to perform a rough cut single point facing operation in a lathe of 5 mm diameter cylinder workpiece…

A: Given Diameter = 5mm Feed rate = 0.5 mm/rev Depth of cut = 4.5mm Specific energy = 3Ws/mm3 To find…

Q: Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm…

A: Given:L1=170 mmL2=165 mmD1=60 mmD2=50 mmN=440 rpmf=0.3 mm/revd=2 mmApproach and overtravel=5 mm

Q: If expanded honeycomb panels were to be machined in a form-milling operation, what precautions would…

A: Honeycomb Structure In composite manufacturing, the honeycomb structure is formed by joining the…

Q: The total work flow times reached 80 hours in one machine and for five works using your evaluation…

A: Given Data : Total work flow time for one machine is t= 80 hours Number of works in the machine is…

Q: How does taper turning process differ from turning process?

A: First of all, we know about that Taper Turning process The process of uniformly reducing the…

Q: A job has to be machined in shaping and the process parameters are given below: a. Length of…

Q: What are the indices for efficient milling?

A: Milling Process: To make additional significant quality and yield white rice from paddy or brutal…

Q: A one machine shop producing bolts has a fixed cost of $2000 and a variable cost of $ 2 per bolts.…

A: solved

Q: In 3-axis milling, the table feedrate is 703.00 mm/min. Using a 10mm endmill to cut the material…

Q: A cylindrical work part 200 mm in diameter and 700mm long is to be turned in an engine lathe.…

A: Given:D=200 mmL=700 mmV=2.3 m/sf=0.32 mm/revd=1.8 mm

Q: What is a Lathe Machine?

A: Given that What is a lathe machine?

Q: Q3. Explain the stages of selecting a material for designing a Ball mill?

A: A ball mill is a machine very similar to a grinder. It is used for the purpose of mixing and…

Q: A surface of 43 mm x 246 mm will be machined by using a shaper and 7 mm deep stock will be removed…

A: Given,

Q: Aluminum bar with 100mm diameter and 500mm long is turnmed down to 88mm diameter, using two passes…

Q: 12. A 600 mm × 30 mm flat surface of a plate is to be finish machined on a shaper. The plate has…

A: …

Q: Give some pictures illustrated about finishing under shaper work processes.

A: A shaper machine is a single-point cutting machine that Is used for machining the vertical and…

Q: 1. Peripheral milling is performed on the top surface of a rectangular work part that is 400 mm long…

A: Note: As per the Bartleby guidelines, only one question can be answered at a time. Therefore, please…

Q: A 6.5 inch long, 0.5 inch diameter stainless steel rod is being reduced to 0.480 inches by turning…

Q: On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The lenght…

Q: How it works Gear machining with shaping machine please elaborate in 200 words

A: In this problem, it is asking about the working of Gear machining with shaping machine.

Q: A hole of 40 mm diameter and 50 mm depth is to be drilled in a milled steel component. The cutting…

Q: Differentiate between single point, multipoint and form tool and Identify the ten examples of single…

A: Cutting tools A cutting tool is a mechanical object which is used for removing the material from the…

Q: Read the description of the operations required to make a part, and considering the production rate,…

A: Given: operations required and production rate To find: Select machine

Q: A cylinder of 155 mm diameter is to be reduced to 150 mm diameter in one turning cut with a feed of…

A: Given:D1=155 mmD2=150 mmfeed, f=0.15 mm/revcutting speed, V=150 m/min

Q: A mild steel block of width 40 mm is being milled using a straight slab cutter 70 mm diameter with…

Q: As a process planner within this company what type of tools and machines would you require to…

A: Given: To find: Types of tools and machines required

Q: Explain reversing and non-reversing two high rolling mills.

Q: What is the feed speed (mm/min) of an end milling cutter if it mills a distance of 300 mm in ten…

A: feed speed,f=300/10 mm/min=30mm/min Feed speed,f =ft*z*N Where,ft=feed per tooth Z=no.of teeth Put…

Q: On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The cutting…

Q: f cut is 2 mm, what is the value of maximum uncut chip thickness when the table feed is 20 mm/min?

Q: A 150 mm long with 12.5 mm in diameter of a stainless steel rod is being reduced in diameter to 12.0…

A: Given:L=150 mmd1=12.5 mmd2=12.0 mmN=400 rpmf=200 mm/min

Q: b):- Calculate the total time to mill a block of aluminum with dimensions of 100 x 40 x 50 to remove…

Q: What is one benefit of indexable end mills?

A: Solution:

Q: Table 1 below shows the cutting speed for some common materials and the feed rates for various…

Q: steel rod 250 mm long and 200 mm in diameter is being reduced to 190 mm in diameter all over its…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Estimate the time required to face mill a 10-inch long, 2-inch wide block of brass with a 6-inch diameter cutter with 10 high-speed steel inserts.
An emergency situation has arisen in the milling department, because the ship carrying a certain quantity of a required part from an overseas supplier sank on Friday evening. A certain number of machines in the department must therefore be dedicated to the production of this part during the next week. A total of 1000 of these parts must be produced, and the production cycle time per part = 16.0 min. Each milling machine used for this rush job must first be set up, which takes 5.0 hr. A scrap rate of 2% can be expected. Assume availability = 100%. (a)If the production week consists of 10 shifts at 8.0 hr/shift, how many machines will be required? (b)It so happens that only two milling machines can be spared for this emergency job, due to other priority jobs in the department. To cope with the emergency situation, plant management has authorized a three-shift operation for six days next week. Can the 1000 replacement parts be completed within these constraints?
explain how a bandsaw, drilling press, and milling machine are used
Assume if a turning machine was producing 50 pieces an hour and the same turningmachine, by the improved methods of doing work is able to produce 100 pieces anhour. Now calculate the productivity (%) and comments on the basis of the results
A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.
Mention the difference between Shaper machine and planer machine?
Suppose in a face milling operation, the dimensions of the workpiece are 5 inches by 10 inches. The cutter is 6 inches in diameter, has 8 teeth, and rotates at 300 rpm. The depth of cut is 0.125 inches and the feedrate is 0.005 inches / tooth. Assume that the specific power requirement for this material is 2 hp min / in3 and that only 75% of the cutter diameter is involved in cutting. Calculate (a) the required power, and (b) the material removal rate.
A mild steel block of width 40 mm is being milled using a straight slab cutter 70 mm diameter with 30 teeth. If the cutter rotates at 40 rpm, and depth of cut is 2 mm, what is the value of maximum uncut chip thickness when the table feed is 20 mm/min?
Estimate the time required to face mill an 344-inch long, 20-in wide grey cast iron hard block with a 12-in diameter cutter with 10 Cermets inserts. Assume a range of machining conditions. What will be the chip thickness for this operation?
to perform a rough cut single point facing operation in a lathe of 5 mm diameter cylinder workpiece made of bronce . Feed rate is 0.5 mm/rev , depth of cut of 4.5mm, and Specific Energy of 3 W-s/mm^3. What is the Material Removal Rate in mm^3/s?
In a classic cutting mill, there is a height difference between the two blades. Why?
When squaring a block on the vertical mill, what surface of the block should be machined first, and why?