The length, width and thickness of a steel sample are 400 mm, 40 mm and 20 mm, respectively Its thickness needs to be uniformly reduced by 2 mm in a single pass by using horizontal slat milling. The milling cutter (diameter: 100 mm, width: 50 mm) has 20 teeth and rotates at 1200 rpm. The feed per tooth is 0.05 mm. The feed direction is along the length of the sample. If the over-travel distance is the same as the approach distance, the approach distance and time taker to complete the required machining task are

The length, width and thickness of a steel sample are 400 mm, 40 mm and 20 mm, respectively Its thickness needs to be uniformly reduced by 2 mm in a single pass by using horizontal slat milling. The milling cutter (diameter: 100 mm, width: 50 mm) has 20 teeth and rotates at 1200 rpm. The feed per tooth is 0.05 mm. The feed direction is along the length of the sample. If the over-travel distance is the same as the approach distance, the approach distance and time taker to complete the required machining task are

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The parameters in the Taylor equation are: n = 0.13 and C = 75 (m/min) for a feed of 0.4 mm/rev. The operator and machine tool rate = $30.00/hr, and the tooling cost per cutting edge = $4.00. It takes 2.0 min to load and unload the workpart and 3.50 min to change tools. Determine: Tutting speed for maximum production rate, Tool life in min of cutting, and Cycle time and cost per unit of product. determine cutting speed for minimum cost.
A high-speed steel tool is used to turn a steel workpart that is 295 mm long and 75 mm in diameter. The parameters in the Taylor equation are: n = 0.15 and C = 80 (m/min) for a feed of 0.5 mm/rev. The operator and machine tool rate = $29.00/hr, and the tooling cost per cutting edge = $3.90. It takes 2.1 min to load and unload the workpart and 3.40 min to change tools. Determine (a) cutting speed for maximum production rate, (b) tool life in min of cutting, and (c) cycle time and cost per unit of product (d) cutting speed for minimum cost and tool life in min of cutting
A vertical boring mill is used to bore the inside diameter of a large batch of tube-shaped parts. The diameter = 28.0 in and the length of the bore = 14.0 in. Current cutting conditions are: speed = 200 ft/min, feed = 0.015 in/rev, and depth = 0.125 in. The parameters of the Taylor equation for the cutting tool in the operation are: n = 0.23 and C = 850 (ft/min). Tool change time = 3.0 min, and tooling cost = $3.50 per cutting edge. The time required to load and unload the parts = 12.0 min, and the cost of machine time on this boring mill = $42.00/hr. Management has decreed that the production rate must be increased by 25%. Is that possible? Assume that feed must remain unchanged in order to achieve the required surface finish. What is the current production rate and the maximum possible production rate for this job?
A cemented carbide tool is used to turn a part with length = 18.0 in and diameter = 3.0 in. The parameters in the Taylor equation are: n = 0.27 and C = 1200. The rate for the operator and machine tool = $33.00/hr, and the tooling cost per cutting edge = $2.00. It takes 3.0 min to load and unload the workpart and 1.50 min to change tools. The feed = 0.013 in/rev. Determine: Cutting speed for maximum production rate, Tool life in min of cutting, and Cycle time and cost per unit of product.
If the maximum chain speed for a sprocket having 19 teeth is 750 fpm, estimate its minimum chain speed.
A machine that produces ball bearings has initially been set so that the true averagediameter of the bearings it produces is .500 in. A bearing is acceptable if itsdiameter is within .004 in. of this target value. Suppose, however, that the settinghas changed during the course of production, so that the bearings have normallydistributed diameters with mean value .499 in. and standard deviation .002 in.What percentage of the bearings produced will not be acceptable?Step by Step Full procedure required.
What general trend did you observe from set-ups 3? Support your answer by using the data gathered.
In an orthogonal cutting test with a bar of 75 mm diameter is reduced to 73 mm by using a HSS tool with arake angle  = 10o, following observations were made: length of the chip, lc = 69.44 mm, cutting ratio r =0.3, the horizontal component of the cutting force, FH = 1450 N, and the vertical component of the cuttingforce, FV = 850 N. The various parameters recorded in this cutting operation are: depth of cut, d = 2 mm;feed rate, f = 0.3 mm/rev, cutting speed, V = 60 m/min. Using Merchant’s theory calculate the following:1) Friction force along rake face2) Normal force acting on rake face3) Shear force along the shear plane4) Normal force acting on shear plane5) The percentage error in shear angle predicted by Merchant’s theory6) Shear velocity7) Chip velocity8) Total work done9) The shear work proportion out of the total work done10) The friction work proportion out of the total work done
You have been asked to work on some design problems and technically support the team working on material removal processes: 1. Technician is turning (lathing) a work material with a shear strength of 270 MPa as shown in Figure 1. The following conditions are used: v = 5.0 m/s, f = 0.30 mm/rev, d = 3.0 mm, and rake angle = 15° in the direction of the chip flow. The resulting chip ratio = 0.5 , material removal rate = 4500 mm3/min ,shear plane angle = 29.02° and the shear strain is = 2.052. Chip Tool R. RF: Turning process.Using the orthogonal model as an approximation of turning, you have been asked to determine: (a) Shear force. (b) Cutting force and thrust force. (c) Friction angle.
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate: 4.1. Energy required to cut a hole. (4) 4.2. Energy required for cutting work per second. (2) 4.3. Maximum fluctuation of energy of the flywheel. (4) 4.4. Mass of the flywheel having radius of gyration of 1.5 m.
A winch drum of diameter 161 mm turning at 12pm lifts a load of 7.5kN. What is the winch output power?
In a turning operation of stainless-steel work part having shear strength = 378 MPa and tensile strength = 420 MPa, a coated carbide tool with a rake angle of 5 degrees is used to reduce its diameter from 100 mm to 93.2 mm with a cutting ratio of 0.45. During this process, a cutting speed of 2.4 m/s and feed of 0.24 mm/rev is used. Using the orthogonal model to approximate the turning process, how much power (W) will the lathe draw in performing this operation if its mechanical efficiency = 90%.