A copper rod of thermal conductivity 360 / mK, diameter 10 cm and length 40 cm acts as a stiffener between two plates maintained at 100°C and 80°C. Determine the heat flow through the rod assuming that the lateral surface of the rod is perfectly insulated.

A copper rod of thermal conductivity 360 / mK, diameter 10 cm and length 40 cm acts as a stiffener between two plates maintained at 100°C and 80°C. Determine the heat flow through the rod assuming that the lateral surface of the rod is perfectly insulated.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.36P

See similar textbooks

Similar questions

2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
Heat is transferred at a rate of 0.1 kW through glass wool insulation (density=100kg/m3) with a 5-cm thickness and 2-m2 area. If the hot surface is at 70C, determine the temperature of the cooler surface.
2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.
The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.
Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
In an experiment to measure the thermal conductivity of a plate of unknown material with area 1 m2 and thickness 0.1m, one of its surfaces is maintained at 100 °C and the other at 20 °C and a heat at the rate of 100 kW was supplied across it. Determine the thermal conductivity of the hot plate. Is the material metallic, non-metallic, or gas/liquid?
A hot surface at 100°C is to be cooled by attaching3-cm-long, 0.25-cm-diameter aluminum pin fins (k = 237 W/m·K) to it, with a center-to-center distance of 0.6 cm. Thetemperature of the surrounding medium is 30°C, and the heattransfer coefficient on the surfaces is 35 W/m2·K. Determine therate of heat transfer from the surface for a 1-m * 1-m sectionof the plate. Also determine the overall effectiveness of the fins.
Water at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. Thewater flow over the surface of the apple creates a convective heat-transfer coefficientof 15 W/(m2-K). Assume the apple can be described as a sphere with a 10 cm diameterand the geometric center is to be reduced to 10°C. The apple properties include thermalconductivity of 0.45 W/(m-K), specific heat of 3.950 kJ/(kg-K), and density of 940 kg/m3.a. Determine the time that the apples must be exposed to the water.b. If the apple is submerged only for 2 hours, what will be its center temperature?
Q4: A spherical object that is made of a material with specific heat=383 J/kg K , and density = 8954 kg/m’. The diameter of the sphere is 5-cm and it is initially at a uniform temperature of 150¢C. It is suddenly exposed to an environment at 20-C having a heat-transfer coefficient h=28W/m? -
A total of 10 rectangular aluminum fins (k =203 W/m·K) are placed on the outside flat surface of anelectronic device. Each fin is 100 mm wide, 20 mm highand 4 mm thick. The fins are located parallel to each otherat a center-to-center distance of 8 mm. The temperature atthe outside surface of the electronic device is 60°C. The airis at 20°C, and the heat transfer coefficient is 100 W/m2·K. Determine (a) the rate of heat loss from the electronic device to the surrounding air and (b) the fin effectiveness.
Calculate the quantity of heat conducted per minute through a duralumin circular disc 119mm diameter and 22.65mm thick when the temperature drop across the thickness of the plate is 9.3°F take the coefficient of thermal conductivity of duralumin as 150 W/m-K. Answer: 22.833 kJ/min
A hot surface at 100°C is to be cooled by attaching 3-cm-long, 0.25-cm-diameter aluminum pin fins (k = 237 W/m · °C) to it, with a center-to-center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m2·°C. Determine the rate of heat transfer (in W) from the surface for a 1-m × 1-m section of the plate. (Hints: Round down your calculated number of fins. Refer to Table 3-3.)