A cube made of an alloy with dimensions of 50 mm x 50 mm x 50 mm is placed into a pressure chamber and subjected to a pressure of 90 MPa. If the modulus of elasticity of the alloy is 100 GPa and Poisson's ratio is 0.28, what will be the length of each side of the cube, assuming that the material remains within the elastic region?

A cube made of an alloy with dimensions of 50 mm x 50 mm x 50 mm is placed into a pressure chamber and subjected to a pressure of 90 MPa. If the modulus of elasticity of the alloy is 100 GPa and Poisson's ratio is 0.28, what will be the length of each side of the cube, assuming that the material remains within the elastic region?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.21P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A cube made of an alloy with dimensions of 50 mm * 50 mm * 50 mm is placed into a pressure chamber and subjected to a pressure of 90 MPa. If the modulus of elasticity of the alloy is 100 GPa and Poisson’s ratio is 0.28, what will be the length of each side of the cube, assuming that the material remains within the elastic region?
A rectangular block of aluminum 30 mm * 60 mm * 90 mm is placed in a pressure chamber and subjected to a pressure of 100 MPa. If the modulus of elasticity is 70 GPa and Poisson’s ratio is 0.333, what will be the decrease in the longest side of the block, assuming that the material remains within the linear elastic region? What will be the decrease in the volume of the block?
A plastic cube with a 100 mm * 100 mm * 100 mm. is placed in a pressurechamber and subjected to a pressure of 100 MPa. If the modulus of elasticityis 7 GPa and Poisson’s ratio is 0.39, what will be the decrease in each side ofthe block, assuming that the material remains within the linear elastic region?What will be the decrease in the volume of the cube?
A steel block has a length of 80 mm, width of 60 mm and thickness of 40 mm. The block is subjected to a uniform hydrostatic pressure of 180 kPa on all its faces. Modulus of elasticity E=200 GPa, Poisson’s ratio ?= 0.29. a.) Determine the bulk modulus of steel, b.) Determine the dilatation (e) of the material if e is the negative of the ratio of load to bulk modulus., and c.) Determine the change in volume of the steel block.
) Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled in tension. (a) Determine its elongation when a load of 20,000 N is applied. (b) What is the modulus of elasticity? (c) What is the strength at a strain offset of 0.002? (d) What is the tensile strength?
The rectangular block shown in Figure is subjected to tension within the elastic range. The increase in the length of a is 2 * 10-3in. and the contraction of b is 3.25 * 10-4 in. If the original lengths of a and b were 2 in. and 1 in., respectively, what is Poisson’s ratio for the material of the specimen?
A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa,and an elastic modulus of 105 GPa. A cylindrical specimen of this alloy12.7 mm in diameter and 250 mm long is stressed in tension and found to elongate 7.6 mm. On the basis of the information given, is it possible to com-pute the magnitude of the load that is necessary to produce this change in length? If so, calculate the load. If not, explain why.
A plastic cube with a 4 in. * 4 in. * 4 in. is placed in a pressure chamber and subjected to a pressure of 15,000 psi. If the modulus of elasticity is 1000 ksi and Poisson’s ratio is 0.49, what will be the decrease in each side of the block,assuming that the material remains within the linear elastic region? What will be the decrease in the volume of the cube?
Consider a rectangular specimen of aluminium has a dimension of 10 ?? × 12.7 ?? is pulled in tension with 35500 N. Calculate the resulting strain. Given the modulus of elasticity is 69 × 103??? and assume that the deformation is elastic.
A plastic cube with a 100 mm X 100 mm X 100 mm. is placed in a pressurechamber and subjected to a pressure of 100 MPa. If the modulus of elasticityis 7 GPa and Poisson’s ratio is 0.39, what will be the decrease in each side ofthe block, assuming that the material remains within the linear elastic region?What will be the decrease in the volume of the cube?