A cylinder C (mass=3 kg) move along horizontal surface with friction factor of ( u =0.1). The cylinder has a pin P. This pin moves in slot of arm which rotate in vertical plane at a rate(ė =0.6 rad/sec). Compute the force exerted by the arm on the pin at the position ( 0 = 60 ). è = 0.6 rad/sec P MI 0.5 m

A cylinder C (mass=3 kg) move along horizontal surface with friction factor of ( u =0.1). The cylinder has a pin P. This pin moves in slot of arm which rotate in vertical plane at a rate(ė =0.6 rad/sec). Compute the force exerted by the arm on the pin at the position ( 0 = 60 ). è = 0.6 rad/sec P MI 0.5 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt andpulley is 0.3, semi V-groove angle is 22.5o and angle of contact of belt with the pulley is 160o. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.Consider the centrifugal tension in the belt.
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless when mass m2 moves a distance 4.94 m up the ramp, how far downward does mass m1 move? d= ?
A bicycle and rider, travelling at 12 km/hr on a level road, have a mass of 105 kg. A brake is applied to the rear wheel, which is 800 mm in diameter. The pressure force on the brake is 80 N and the coefficient of friction is 0.06. Find the distance covered by the bicycle and the number of turns of its wheel before coming to rest.
A pile-driver hammer has a mass of 300 kg and is to be raised 16 m in 4 sec. The total friction on the guides is constant at 400 N. What constant pull must be exerted on the cable?
A rigid gate of a flood control structure in a river is 6 m wide by 4 m high and weighs 10 kN. With its longer edge horizontal, it is moved up and down with its short edges sliding in vertical channel guides. Evaluate the force, in kN, needed to raise the gate when the surface of the water is 2 m. above its top edge. There is no water on thedownstream side of the gate. The coefficient of friction between the gate and the channel guides is 0.10. Neglect the buoyant effect of the water on the gate and the weight of the cables connected to the gate.a. 104 b. 94 c. 110 d. 92
If there is no friction between shaft AB and the collar, what angular velocity Ö must the mechanism have to keep the collar at r= 660 mm from the vertical axis? Consider the same mechanism again, with m = 3.3 kg, d = 275 mm, k = 180 N/m, only now, instead of being smooth, the collar and shaft have a maximumcoefficient of friction of 0.74. What is the minimum angular velocity required to keep the collar at a constant distance r= 660 mm from the axis of rotation?
A water-cooling system for a hydro generator uses a drum to delivercooling fluid (figure Q1 Below). To stop the system a single shoe brake is used. Thewidth of shoe contact with the drum is 40 mm. The friction material provides acoefficient of friction of 0.3, and delivers an average pressure of 600 kPa, based onthe projected area of contact. Use the short-shoe approximate relationships. The initialdrum speed is 1200 rpm. (a) What value of force F can be applied without exceeding the allowablecontact pressure?
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless what is the acceleration of mass m2 on the inclined plane? take positive acceleration to be up the ramp a2 = ?
A 1855 kg car has a velocity of 100 km/h when the brakes are fully applied. Assume modern traction control eliminates tire skidding. Determine time and distance to stop the car if dry-pavement static friction coefficient is 0.8.Creat a conclusion for this problem.
200lp box is at rest in the beginning on horizontal surface and force T=100lb and P applied shown. coefficient of static and kinetic friction is us= 0.3 and uk=0.2. find acceleration of block if p=100lb and p=250lb
A centrifugal clutch has four shoes, each of mass 0·35 kg. When at rest, the radialclearance between the shoes and the clutch drum is 15 mm and the radius to the centre ofgravity of the shoes is 225 mm. The shoes are held on retaining springs of stiffness 10kN/m and the internal diameter of the clutch drum is 600 mm. The coefficient of frictionbetween the drum and the shoes is 0·3.Determine:(a) The speed (in rev/min) at which the clutch starts to engage. For a rotational speed of 1200 rev/min:(b) The force each shoe exerts on the drum. (c) The torque transmitted. (d) The power transmitted.