A cylinder with a diameter of 0.5 m and a height of 1.8 m is shown below. The water flows through a flap valve (attached to the pair) with an opening of 0.075 m in diameter. It must be pushed up to open the valve. Determine the force to open the valve.

A cylinder with a diameter of 0.5 m and a height of 1.8 m is shown below. The water flows through a flap valve (attached to the pair) with an opening of 0.075 m in diameter. It must be pushed up to open the valve. Determine the force to open the valve.

Name: A cylinder with a diameter of 0.5 m and a height of 1.8 m is shown bel
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A cylinder with a diameter of 0.5 m and a height of 1.8 m is shown below. The water flows through a flap valve (attached to the pair) with an opening of 0.075 m in diameter. It must be pushed up to open the valve. Determine the force to open the valv

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.76P: A 6-in. diameter hole is drilled in the conical frustum. Calculate the volume and the surface area...

See similar textbooks

Similar questions

Determine the depth of a liquid needed to create a pressure difference of 225 kPa if the liquid is (a) water,(b) air at standard conditions, (c) mercury, and (d ) oil with S ¼ 0.86.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown . The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Using appropriate software, investigate the effect of water depth on the force exerted on the plate by the ridge. Let the water depth vary from 0 to 5 m in increments of 0.5 m. Tabulate and plot your results.
Answer is: V = 14.17 ft/s
If the pressure in a tank of oil (sp gr 0.85) is 375kn/m2, what is the equivalent head; (a) in meters of the oil; (b) in meters of water; (c) in meters of mercury? NOTE: Clear handwritten solution
Five sewer pipes, each a 2-m-diameter clay tile piperunning half full on a slope of 0.25°, empty into a singleasphalt pipe, also laid out at 0.25°. If the large pipe is alsoto run half full, what should be its diameter?
End D of a 2.5 long uniformly plain wooden rod( s.g=0.7) is held 0.3m below the surface of still water. (a.) How much of the rod remains above the water surface? (b.) if the rod diameter is 25mm what force of D is required to hold it in place ?
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
Provide complete solution and diagram for this problem. What is the equivalent head of 15cm mercury in water ? A. 10m B. 1.36m C. 2.04m D. 16.34m
The greatest known ocean depth is the Mariana Trench, in the Pacific Ocean, which is at 11,034 m. At this depth the specific gravity of seawater is approximately 10,520 N / m3. On the surface ρg P 10,050 N / m3. Estimate the pressure at this depth in atmosphere
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
A sluice gate is a device that is fitted in a sluice or fluid canal to operate and control the fluid flow. Oil flows in a canal and sluice gate has a breadth of 8m wide and 6m deep. Let the oil density = 850kg/ m^3. Determine : hydroelectric force in(KN) acting on the sluice gate when the oil is level with the top of the sluice gate.?
Capillary rise in the glass tube used for measuring water level isnot to exceed 0.5 mm. Determine its minimum size, given thatsurface tension for water in contact with air = 0.07112 N/m.