Q.7. In an Aeroplan model of size 1/10 of its prototype thepressure drop is 7.5 kN/m². The model is tested in water. Findthe corresponding pressure drop in the prototype. Take Densityof air = 1.24 kg/m³. Density of water = 1000 kg/m³.Viscosity ofair = 0.00018 poise Viscosity of water = 0.01 poise

Name: Q.7. In an Aeroplan model of size 1/10 of its prototype thepressure d
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q.7. In an Aeroplan model of size 1/10 of its prototype thepressure drop is 7.5 kN/m². The model is tested in water. Findthe corresponding pressure drop in the prototype. Take Densityof air = 1.24 kg/m³. Density of water = 1000 kg/m³.Viscosity ofair

Answered: Image /qna-images/answer/9c79194e-7b09-48fe-ae12-a0e904960311.jpg

Answered: model of size 1/10 kN/m². The mod…

Engineering

Mechanical Engineering

model of size 1/10 kN/m². The mod pressure drop in th Density of water =

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

When a sphere falls freely through a homogeneous fluid, it reaches a terminal velocity at which the weight of the sphere is balanced by the buoyant force and the frictional resistance of the fluid. Make a dimensional analysis of this problem and indicate how experimental data for this problem could be correlated. Neglect compressibility effects and the influence of surface roughness.
The pressure drop in a venturi meter (Fig. P3.128) varies onlywith the fluid density, pipe approach velocity, and diameterratio of the meter. A model venturi meter tested in water at20 ° C shows a 5-kPa drop when the approach velocity is 4 m/s.A geometrically similar prototype meter is used to measuregasoline at 20 °C and a flow rate of 9 m 3 /min. If the prototypepressure gage is most accurate at 15 kPa, what should theupstream pipe diameter be?
The variables in a Saybolt viscometer are the time (t) required to empty a certain volume of oil of density (ρ) and viscosity (μ), a length (L) representing the dimensions of the viscometer, and the gravitational acceleration (g). Using the Buckingham Pi-theorem, show that
A small wind turbine is tested in a wind tunnel using the following model parameters: ρ = 1.2 kg/m3 , µ = 1.81x10-5 Ns/m2 , v = 12 m/s, A = 0.03 m2 and Cp is measured as 0.42. Assuming dynamic similarity exists, calculate the power output of a full-size turbine of diameter 60 m operating in air of density 1.3 kg/m3 and viscosity µ = 1.73x10-5 Ns/m2 with wind speeds of 15 m/s
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3 Please.. explain more easy
Q.10. To predict the drag on an aircraft at a flight speed of 150 m/s, where the condition of air is such that the local speed of sound is 310 m/s, a pressurized low temperature tunnel is used. Density, viscosity and local sonic velocity at tunnel condition are 7.5 kg/m³, 1.22 x 10-5 Ns/m² and 290 m/s. Determine the flow velocity and the scale of the model. Assume full dynamic similarity should be maintained. Density and viscosity at the operating conditions are 1.2 kg/m³ and 1.8 x 10 Ns/m².
A liquid with a specific gravity of 4.7 and a viscosity of 1.3 cp flows through a smooth pipe of unknown diameter, resulting in a pressure drop of 0.183 lbf/in² for 1.73 mi. What is the pipe diameter in inches if the mass flowrate is 5,900 lb/hr?A. 3.64 inB. 0.44 inC. 5.74 inD. 0.005 in
Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V, pressure difference DP, fluid density r and viscosity m. a)Determine dimensionless P groups. b)A test is to be performed for a large pump that delivers 1.5 m3 /s of water from 40 cm diameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impeller is to be used. What flow rate should be used and what would be the pressure rise in model pump. Note: The model fluid is water at same temperature as the water in the prototype.
The force, F, acting on a billboard due to wind depends on it length, l, height, h, the modulus of elasticity of the board, E, and the specific weight, γa, of the air. Using dimensional analysis, find an appropriate dimensionless relationship.
The pressure coefficient is defined by the ratio between the static pressure difference and the dynamic pressure (pictured): Where P is the static pressure [Pa], P∞ is the reference static pressure [Pa], ρ is the density [kg/m3], and V is the velocity [m/s]. Using the primary dimensions and their units, show that the pressure coefficient is dimensionless.
A dimensionless combination of variables that is important in the study of viscous flow through pipes is called the Reynolds number, Re, defined as ???/? where, as indicated in Fig. 11, ? is the fluid density, V the mean fluid velocity, D the pipe diameter, and the fluid viscosity. A Newtonian fluid having a viscosity of 0.38 ? . ?/?² and a specific gravity of 0.91 flows through a 25‐mmdiameter pipe with a velocity of 2.6 ?/?. Determine the value of the Reynolds number using (a) SI units, and (b) BG units.