A cylindrical block of aluminum of diameter of 50cm and height 5cm slides down a smooth inclined surface as shown in Fig. Determine the terminal velocity, steady speed achieved by an object freely falling through a fluid, of the block if the 0.1 mm gap between the block and the surface contains SAE 10 W oil at 20C. Assume the velocity distribution in the gap is linear. 0.1 mm gap 20°

A cylindrical block of aluminum of diameter of 50cm and height 5cm slides down a smooth inclined surface as shown in Fig. Determine the terminal velocity, steady speed achieved by an object freely falling through a fluid, of the block if the 0.1 mm gap between the block and the surface contains SAE 10 W oil at 20C. Assume the velocity distribution in the gap is linear. 0.1 mm gap 20°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A large plate is pulled at a constant speed of U = 4 m/s over a fixed plate on 5-mm-thick engine oil film at 20°C. Assuming a half-parabolic velocity profile in the oil film, as sketched, determine the shear stress developed on the upper plate and its direction. What would happen if a linear velocity profile were assumed?
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
A plate 0.05 mm distant from a fixed plate, moves at 0.5 m/s and requires force 5 N/m² to maintain this speed. Determine the fluid viscosity between plates
Consider the incompressible viscous flow of air between two infinitelylong parallel plates separated by a distance h. The bottom plate isstationary, and the top plate is moving at the constant velocity ue in thedirection of the plate. Assume that no pressure gradient exists in the flowdirection.a. Obtain an expression for the variation of velocity between the plates.b. If T = constant = 320 K, ue = 30 m/s, and h = 0.01 m, calculate theshear stress on the top and bottom plates.
A 1-m-diameter sphere is being towed at speed V in freshwater at 20°C as shown in Fig. Assuming inviscidtheory with an undistorted free surface, estimate the speedV in m/s at which cavitation will first appear on the spheresurface. Where will cavitation appear? For this condition,what will be the pressure at point A on the sphere, which is45° up from the direction of travel?
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
An oil drop has a density (?1) of (560+R) kg/m3. The terminal velocity of a spherical drop of thisoil falling in air at the room temperature is (15 + R) cm/s. At the room temperature, air density(?2) is 1.2 kg/m3and its viscosity is 18 μPa.s. Find the radius of the droplet. Consider g =9.81 ??
The belt in the Ögure moves at steady velocity V and skims the top of a tank of oil having viscosity. (a) Develop and expression for the required belt drive power in terms of h, L, b, V , and . Recalthat, for steady motion, power is equal to force velocity.(b) What power is required if the belt moves at 5 m/s over SAE 50W oil ( = 0:86 kg/ms) withh = 2 cm, L = 2 m, and b = 0:5 m
Consider a commercial airliner flying at a speed of 540 mph (relative to the air) at analtitude of 30,000 feet. (c) With a mean molar mass of M = 28.9 g/mol, determine the Reynolds number andMach number in flight. Justify your choice of characteristic length by referencinga commercial aircraft currently in service.(d) Is this flow inviscid or viscous? Is this flow subsonic or supersonic? Qualitativelydescribe the differences between these flight regimes.
Before cooking dinner, I pour oil into the center of a frying pan at a rate of 10^-6 m^3 /s. Once it hits the pan, the oil flows outwards from the center in a 2mm-thick layer, forming a perfectly circular disc. Assume the oil velocity is purely radial in this thin layer, and it is uniform in the vertical direction. a. What is the oil velocity 5 cm from the center? b. What is the oil velocity 10 cm from the center? ***Ps. if you can just guide me through the concept and pointing out which equation to use please***
A square block is weighing 300 N and having a length of 20 cm on one edge slips on a 20° inclined surface in which there is a film of SAE 30 at 10°C oil. What is the terminal velocity of the block down the incline if the oil thickness at this condition is 1 mm?
Water flows at a velocity of 1.2 m/s over a flat plate 1.2 m long. Assume 1/7thpower law and determine the boundary layer thickness and displacementthickness. Compare the values with values calculated using laminar flowcorrelations. υ = 1 × 10−6m2/s.