A three-legged tube is filled with oil (SG =0.88). As shown, the surfaces of oil in all legs are at the same height when the tube is at rest. Calculate, (a) the maximum angular velocity, w (in rpm), that the tube can be rotated at leg 1 without causing any spillage of oil; (b) the new height (in cm) of oil in leg 2; and (c), the corresponding pressure (in Pa) at point A. The diameter of the tube is the same on all its legs. h- 43cm а — 19cm b- 11cm с -76сm A.

A three-legged tube is filled with oil (SG =0.88). As shown, the surfaces of oil in all legs are at the same height when the tube is at rest. Calculate, (a) the maximum angular velocity, w (in rpm), that the tube can be rotated at leg 1 without causing any spillage of oil; (b) the new height (in cm) of oil in leg 2; and (c), the corresponding pressure (in Pa) at point A. The diameter of the tube is the same on all its legs. h- 43cm а — 19cm b- 11cm с -76сm A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Piston A has a cross-section of 1,200 cm^2 while that of piston B is 950 cm^2 with the latter higher than piston A by 1.75 m. If the intervening passages are filled with oil (s= 0.8), what is the difference in pressure between A and B?
The belt in the Ögure moves at steady velocity V and skims the top of a tank of oil having viscosity. (a) Develop and expression for the required belt drive power in terms of h, L, b, V , and . Recalthat, for steady motion, power is equal to force velocity.(b) What power is required if the belt moves at 5 m/s over SAE 50W oil ( = 0:86 kg/ms) withh = 2 cm, L = 2 m, and b = 0:5 m
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
Using a flexible drinking straw and a ruler, explain how you would measure the water flow velocity in a river.
Explain the work of Nozzles and diffusers are shaped so that they cause large changes in fluid velocities and thus kinetic energies.
Determine the angular velocity (in rpm) required for an open 100-cm diameter cylindrical tank 250cm high if it contains water 150cm deep at the following condition. When the water could just reach the rim of the tank.
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
Impact of Jet In your own words, explain the reason for moving the counterbalance, putting different weight on the pan, and measuring the length of the weight pan and counterbalance distance. 2. Based on your observation, what is the difference between the force produced by the jet impact on a flat vane and an inclined vane? Explain the phenomenon.
From Table A.3, the density of glycerin at standard conditionsis about 1260 kg/m3 . At a very high pressure of 8000 lb/in2 , itsdensity increases to approximately 1275 kg/m3 . Use this datato estimate the speed of sound of glycerin, in ft/s.
A solid cone of angle 2θ, mass (m), base radius (r0), and density (ρc), is rotating with angular velocity (w0) on its conical seat. The clearance (h) is filled with oil of viscosity (μ). Neglecting air resistance, determine: a) an expression for the moment (M) as a function of r0, w0,μ,θ, and h. b) an expression for the angular velocity (w) for t≥0 as a function of w0,μ,θ,h, r0,m and t if an external torque is not applied. If the radius of gyration of the cone is 16 cm, determine: c ) the value of the angular momentum and velocity if w0=60RPM,h=0.05mm,θ=30°,μ=0.98cPoise , m=20kg, t=2.0s
The density of water is 1000 kg/m3, and it has a viscosity of 0.001 kg/(m*s). What is the Reynolds number for a flow with speed = 0.2 m/s and depth = 0.1 m?
A water jet of an area of 0.03 m² impinges normal on a fixed plate. If a force of 1 kN is produced as a result of the impact, the velocity of the jet would be