A cylindrical container whose weight is titet Ibf is inverted and pressed into the water, as shown in the given figure. Determine the differential height h of the manometer and the force F needed to hold the container at the position shown. (specific weight of water is 62.22 lbf/ft³). 2).55 Manometer fluid Air S.G. = 2.1 d 9.84 in 7.87 in -hwter Water

A cylindrical container whose weight is titet Ibf is inverted and pressed into the water, as shown in the given figure. Determine the differential height h of the manometer and the force F needed to hold the container at the position shown. (specific weight of water is 62.22 lbf/ft³). 2).55 Manometer fluid Air S.G. = 2.1 d 9.84 in 7.87 in -hwter Water

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 49P

See similar textbooks

Similar questions

In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
Q1(a) Explain the difference between wetting fluid and non-wetting fluid (b) The 60m X 60m rectangular gate shown in Figure Q1(b) has its top edge located 3m vertically below the water surface. The gate is to be opened from its lower edge by applying a normal force by the shaft. Determine the minimum force F required to open the water gate. (Ignore Patm in all your calculations)
Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the 2m x 5m gate shown in the figure. Pressure of air = 47 kPa Fluids: fluid a (s=3.8) fluid b (s=0.27) fluid c (s=1.68) h1= 0.9 m h2= 1.6 m h3= 3.9 m Round your answers in 3 decimal places
Show complete and detailed solution. Show FBD of the figure. What is the smallest mass of B to make the system in equilibrium while neglecting the friction between the string and the ramp? Mass of Block A = 45kg Coefficient of Block A, Block B, and Ramp C = 0.10
A wooden beam ( sg= 0.64) is 150 mm by 150 mm by 6m and is hinged at A as shown in the figure. Assuming unit weight of water is 9.79 kN/cu.m. a.) Determine the length of the beam submerged in water? b.) At what angle will the beam float in the water? c.) And determine the buoyant force that causes the beam to be submerged at an angle of theta from horizontal. Please answer this correctly PLEASE :(
Based on the provided differential-type manometer, calculate the difference in the pressure between points A and B (as in Δp = pA - pB = ?). SG of oil is 0.8
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?
Plss help ASAP A)resulting acceleration in (m/s^2) B)estimate resulting pressure at the bottom of the tank in kilopascal
A section of a reinforced concrete elevator shaft is shown in the figure. Compute the following: a. Centroid of section; b. Centroidal Moments of Inertia; and c. Rigidity about the centroidal axes. Consider the effect of shear deflection. Assume h = 15m, P = 1000 kN, and f'c = 24 MPa. ..need original and complete answer
Given beam loaded as shown below. Assuming EI is constant. 1. Which of the following gives the location of maximum deflection. a. 2.212 m b. 1.958 m c. 1.334 m d. 1.456 m 2. Which of the following the value of maximum deflection. a. 29.4/EI b. 17.5/EI c. 20.7/EI d. 14.2/EI
The differential manometer shown in figure 4 is used to measure pressure difference between pipe A and B. Pipe A is conveying water while pipe B is conveying air. If the pressure at B is 12kPa calculate the pressure at A. Figure 4. (a) 35kPa (b) 12kPa (c) 23kPa (d) 24kPa
A cylindrical tank containing a fluid (sg = 0.75) is accelerated upward by a net force of 40 lb. The volume of the fluid is 1.60 cu. ft. If the depth of the fluid is 3 ft, determine the force acting on the bottom of the tank. 4 decimal places answers