PROBLEM 1: The vertical member consists of 2 (two) unequal legs with long legs back to back are welded to the 8 mm thíck gusset plate. Size of angle = 75 mm x 50 mm x 6 mm thíck. Area of two angles = 1535 mm2 Weld thickness = 5 mm Fy = 248 MPa F= 400 MPa U= 0.82 (reduction factor) Fw= 485 MPa (E 70 xx electrodes) y = 25 mm O Determine tensile strength of the angular section. ® Determine the length of 5 mm fillet weld Li so that each fillet weld is equally stress in shear. Determine the length of 5 mm fillet weld L2 so that each fillet weld is equally stress in shear.

PROBLEM 1: The vertical member consists of 2 (two) unequal legs with long legs back to back are welded to the 8 mm thíck gusset plate. Size of angle = 75 mm x 50 mm x 6 mm thíck. Area of two angles = 1535 mm2 Weld thickness = 5 mm Fy = 248 MPa F= 400 MPa U= 0.82 (reduction factor) Fw= 485 MPa (E 70 xx electrodes) y = 25 mm O Determine tensile strength of the angular section. ® Determine the length of 5 mm fillet weld Li so that each fillet weld is equally stress in shear. Determine the length of 5 mm fillet weld L2 so that each fillet weld is equally stress in shear.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a. Calculate "P" in KN considering tension failure on gross area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Exp.joint
Two 10"-15.3 lb channels are welded together as shown in the figure. Find the moment of area of the upper channel about the horizontal centroidal axis Xo of the entire section.
The rivet group connects two narrow lengths of plate, one of which carries a 15 kN load. If the ultimate shear strength t of a rivet is 350 N/mm² and its failure strength in compression o is 600 N/mm², determine the minimum allowable values of rivet diameter d (mm) and plate thickness t (mm).
Determine if the axial stress in nember CF if the area of each member is 75 mm^2. Indicate if T or C.
A triple riveted lap joint with zig-zag riveting is to be designed to connect two plates of 6 mm thickness. Determine the dia. of rivet, pitch of rivets and distance between the rows of rivet. Indicate how the joint will fail. Assume : 0, = 120 MPa ; r = 100 MPa and o, = 150 MPa.
The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18Mg block is attached. Each steel bar has an area of 566mm^2 and E=200Gpa. For the bronze barn the area is 866mm^2 and E=83Gpa. Find the stresses developed in each bar.
A member is made of the following materials: steel, brass and copper, the constants are listed below:STEEL:length: 300mmcoeff. of thermal expansion: 12(10^-6)/degree Carea: 200mm^2E= 200 GPaBRASS:L= 200mmA= 450mm^2Coeff of thermal expansion: 21(10^-6)/degree CE= 100 GPaCOPPER:L= 100mmA= 515mm^2Coeff. of thermal expansion: 17(10^-6)/degree CE= 120 GPaRigid supports are located at each end of the member. What is the force exerted on the supports if the temperature increases by 6 degrees C?
A round steel pipe is 3 meters long, with an outside diameter of 6 cm. The pipe stretches .2cm. with a tensile pull of 11.12 kN. If the "E" for the pipe is 462 GN/m2 find the inside diameter of the pipe.
Please do both qestions Q1 - Inner diameter = 47.0 mm Q2 - Inner diameter = 12.6 mm
an 8 m long steel is pinned at the top and fixed at the bottom. the column is provided with lateral support 3m from the top in the weak direction. the properties of the column section are as follows: ix = 178.1x10^6 mm^4 ly = 18.8x10^6 mm^4 a = 8129 mm^2 fy = 400 mpa a. what is the critical effective slenderness ratio? %3d %3d b. what is the buckling stress of the column? c. calculate the critical load pc in kn
Determine the block shear capacity of the following plate with holes shown. The holes are 0.026m in diameter. The plate is 0.060m thick. Allowable shear stress = 120MPa, allowable tension stress = 160 MPa.