A cylindrical machine part moves within a surrounding cylinder. The centrelines of the part and the surrounding cylinder are coincident. The cylinder is full of an oil (viscosity 0.25kg/ms) that is not flowing i.e. no pressure gradient is applied. What is the value of the viscous force exerted on the machine part as it moves along the cylinder at a speed of 9m/s? • The machine part is 0.06m long and has a radius of 0.041m. • The ratio of the machine part radius to the cylinder radius is 0.98. • Assume that the flow is dominated by viscous forces. • Give your answer as an absolute value i.e. no negative sign, in Newtons to one decimal place.

A cylindrical machine part moves within a surrounding cylinder. The centrelines of the part and the surrounding cylinder are coincident. The cylinder is full of an oil (viscosity 0.25kg/ms) that is not flowing i.e. no pressure gradient is applied. What is the value of the viscous force exerted on the machine part as it moves along the cylinder at a speed of 9m/s? • The machine part is 0.06m long and has a radius of 0.041m. • The ratio of the machine part radius to the cylinder radius is 0.98. • Assume that the flow is dominated by viscous forces. • Give your answer as an absolute value i.e. no negative sign, in Newtons to one decimal place.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
Two parallel flat plates are spaced 2 in. apart. One plate is moving at a velocity of 10 ft/min and the other is moving in the opposite direction at 35 ft/min. The viscosity of the fluid between the plates is constant at 363 lb/ft-hr. Calculate the stress on each plate. Calculate the fluid velocity profile expression for the system and fluid velocities at ½ in. intervals from plate to plate.
A fluid with a velocity of 30 m/s flows past a sphere with a radius of 40 mm. The density and viscosity of the fluid is1.32 kg/m3 and 3.6 x 10-5Pa.s, respectively. Calculate the force exerted on the sphere? (CD = 0.31)
A cylinder of mass m slides down from rest in a vertical tube whose inner surface is covered by a viscous oil of film thickness h. If the diameter and height of the cylinder are D and L, respectively, derive an expression for the velocity of the cylinder as a function of time, t. Discuss what will happen as t → ∞. Can this device serve as a viscometer?
A sled with two runners slides along a thin horizontal layer of water between the ice and the runners. The horizontal force that the water puts on the runners is equal to 2.4 lb when the sled's speed is 50 ft/s. The total area of both runners in contact with the water is 0.04 ft2, and the viscosity of the water is 3.5x10 lbs/ft2. Determine the thickness of the water layer under the runners. Assume a linear velocity distribution in the water layer.
Students conducted an experiment to evaluate the velocity profile,u(y), of a fluid flowing over a flat plate (Figure-3). Different students have reported different variations of velocity with vertical distance y from the plate as below. u(y)=y^2−2aby Obtain a relation of shear stress and wall shear stress in terms of a and b using the appropriate velocity profile. Calculate the shear stress at location y = 0.005 m, if the viscosity of the fluid is 60 Pa-s.
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
An oil film of thickness 1.5 mm is used for lubrication between asquare plate of size 0.9 m × 0.9 m and an inclined plane having anangle of inclination 200. The weight of the square plate is 392.4 N andit slides down the plane with a uniform velocity of 0.2 m/s. Find thedynamic viscosity of the oil
In a stream of glycerine in motion, at a certain point the velocity gradient is 0.25 meter per sec per meter. The mass density of fluid is 1268.4 kg per cubic meter and kinematic viscosity is 6.30 x 10^-4 square meter per second. Calculate the shear stress in Pascal at the point.
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N).
A shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant clearance. If the power required to rotate the shaft is 2204 W, find the viscosity of lubricant oil in the clearance. Take length of sleeve as 150 mm. Assume a linear velocity profile in the fluid film.