A cylindrical rod 380 mm (15.0 in.) long and having a diameter of 10.0 mm (0.40 in.), is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.9 mm (0.035 in.) when the applied load is 24,500 N (5500 Ibf), which of the four metals or alloys listed in the following table is a possible candidate? Modulus Yield Tensile Material of Elasticity Strength Strength (MPa) (GPa) (МPа) Aluminum alloy 70 255 420 Brass alloy 100 345 420 Сopper 110 250 290 Steel alloy 207 450 550 O Steel alloy O Aluminum alloy O Copper O Brass alloy

A cylindrical rod 380 mm (15.0 in.) long and having a diameter of 10.0 mm (0.40 in.), is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.9 mm (0.035 in.) when the applied load is 24,500 N (5500 Ibf), which of the four metals or alloys listed in the following table is a possible candidate? Modulus Yield Tensile Material of Elasticity Strength Strength (MPa) (GPa) (МPа) Aluminum alloy 70 255 420 Brass alloy 100 345 420 Сopper 110 250 290 Steel alloy 207 450 550 O Steel alloy O Aluminum alloy O Copper O Brass alloy

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.33P: According to Figure 5-20, is ii possible to completely separate one of the four materials from the...

See similar textbooks

Similar questions

A cylindrical rod 500 m (20.0 in) long, having a diameter of 12.7 mm (0.50 in.), is to be subjected to a tensile load. If the rod is to be experienced neither plastic deformation nor an elongation of more than 1.3 mm (0.05 in.) when the applied load is 29,000 N (6500 lb), which of the four metals or alloys listed are possible candidates? Justify your choice(s).
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded
A cylindrical rod 360 mm long, having a diameter of 10.0 mm, is to be subjected to a tensile load. If the rodis to experience neither plastic deformation nor an elongation of more than 0.9 mm when the applied load is22500 N, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).Material Modulus ofElasticity (GPa)Yield Strength(MPa)TensileStrength (MPa)Aluminum alloy 70 255 420Brass alloy 100 345 420Copper 110 210 290Steel alloy 207 450 550
A cylindrical rod with a diameter of 15.24 mm and a gauge length of 400mm is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.45 mm when the applied load is 31,000 N, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).
A cylindrical rod 600 mm long and having a diameter 13.2 mm is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 1.4 mm when the applied load is 30 KN. Which of the four metals or alloys listed below are possible candidates. Justify the answer with calculations Material modulus of elasticity(gpa) yield strength(mpa) tensile strength(mpa) Aluminium alloy 70 255 420 Brass alloy 100 345 420 Copper 110 210 275 Steel alloy 207 450 550
A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa. Express your final answer in N.m to the nearest whole number. Do not include the unit in your answe
A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of 11.6 * 106 psi. The rod is to be subjected to a torque T.What is the minimum required length L of the rod so that the cross section at one end can be rotated 60° with respect to the other end without exceeding an allowable shear stress of 45 * 103 psi?
Problem 1 A steel connecting rod with length of 6 meters and is to be subjected to a tensile load of 70 KN. A. What will be the diameter if the total elongation is not to exceed 4 mm. B. Choose a stainless-steel material based on yield strength and dead load.
A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.018 in. when the applied load is 7,000 lb, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).
A high-strength steel band saw, 27 mm wide, runs over pulleys 1100 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 350? Assume E = 210 GPa. Answer must be in mm.
A steel tube with 3cm outside diameter, 0.25cm thick, and 4m long is covered and lined throughout with copper tubes 0.20cm thick. The three tubes are joined together at their ends. What is the maximum compressive load that can be applied to the top such that the total deformation does not exceed 0.50mm? Esteel = 200 GPa & Ecopper = 110 GPa.
Tempered rod with length of c= 8m and cross sectional dimensions a=297 mm is carrying an axial load P=75kN if the modulus of elasticity is 185gpa determine the elongation