A cylindrical rod 600 mm long and having a diameter 13.2 mm is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 1.4 mm when the applied load is 30 KN. Which of the four metals or alloys listed below are possible candidates. Justify the answer with calculations Material modulus of elasticity(gpa) yield strength(mpa) tensile strength(mpa) Aluminium alloy 70 255 420 Brass alloy 100 345 420 Copper  110 210 275 Steel alloy 207 450 550

Q: A 30mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is…

A: Do=800.5mm Di=800mm E=200GPa

Q: The assembly shown in the figure consists of 10 mm diameter titanium (E = 125 GPa) rods AB and CD,…

A:

Q: A tensile load of 50,000 lb is applied to a metal bar with a 0.6 in. * 0.6 in.cross section and a…

A: Given: The tensile load is 50,000 lb. The area of the metal bar is 0.6 in x 0.6 in. The gauge length…

Q: A high strength steel with modulus of elasticity of A N/mm, yield strength of B N/mm and crushing…

A: Given Data:E = 239000N/mm2σy= 1300N/mm2Crushing Strength, = σc= 1740N/mm2Strain at the time of…

Q: A composite column member is fabricated on top of a base plate as shown in the figure. What should…

A:

Q: The composite member is shown in the figure. If the rigid bar remains horizontal after the loading…

A:

Q: A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is…

A: Given data-

Q: A composite column member is fabricated on top of a base plate as shown in the figure. What should…

A:

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: The given data is: Tensile Load on metallic bar (P) = 190 kN Diameter of bar (d) = 16 mm Length of…

Q: A rectangular bar 10millimeters in Length and 20 millimeters in width is held at its upper end. The…

A: Strength of material: It refers to different numerical methods stresses and strains in structural…

Q: A copper tube having a cross sectional area of 2000 mm2 and a length of 300 mm is rigidly fixed to…

A: GIVEN: Area of copper tube(AC) = 2000mm2length of copper tube (LC) = 300mm4 steel boltseach diameter…

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine…

A: Please find the answer in the below attachments

Q: A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile…

A: Answer Based on the given data, we can calculate the minimum Elastic Modulus required for possible…

Q: 4.) A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile…

A: Length of rod (L)  = 100 mmDiameter of rod (d) = 10 mmC/s Area of Rod (A) = π4d2 = π4×102 = 78.54…

Q: A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test…

A: A. (1) The stress in the bar is given by: σ=LoadArea Given data, Load = 6.4 kN Area =…

Q: Q2\ A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in…

A: When the deviation exceeds the maximum allowable value, the amount of radiation obtained on the…

Q: Impact value is used to measure? А. Hardness В. Toughness C. Wheel load D. Strength

A: To find out the impact value is used to measure.

Q: The cantilever beam shown in the figure below carries a downward load that varies from 300 to 700…

A:

Q: A cylindrical rod 380 mm (15.0 in.) long and having a diameter of 10.0 mm (0.40 in.), is to be…

A:

Q: Problem # A tensile load of 220 KN is applied to a round metal bar with a diameter of 16 mm and a…

A: Data given: Tensile load = 220 kN = 220 × 103 N Diameter of the bar ϕ= 16 mm gauge length L = 50 mm…

Q: Determine the minimum diameter d of the rod to safely support the load. The rod is made of a…

A: Calculate the maximum moment of beam and shear force Calculate the moment of inertia of a circle and…

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gauge length…

A: The Poisson’s ratio is given by,

Q: A cylindrical rod with a diameter of 15.24 mm and a gauge length of 400 mm is subjected to a tensile…

A: Solution

Q: A cylindrical rod 500 m (20.0 in) long, having a diameter of 12.7 mm (0.50 in.), is to be subjected…

A:

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

A:

Q: A cylindrical rod with a diameter of 15.24 mm and a gauge length of 400mm is subjected to a tensile…

A: Given: The diameter of the cylindrical rod is 15.24 mm. The gauge length of the cylindrical rod is…

Q: Give me right solution  A steel bar that is 28 feet long is subjected to a 251 kip load. Maximum…

A:

Q: A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa,and an elastic modulus…

A: Yield Strength: It is defined as the stress that a material can withstand without any permanent…

Q: AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGTHS SHOWN IN THE FIGURE. IF E= 85 KPa, COMPUTE THE…

A: Given data in question  Load Diameter  Length  Elasticity modulus  To find out  Elongation

Q: The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can…

A: Given :

Q: If a steel column with cross-sectional area A = 1000 mm^2 modulus of elasticity E = 200 MPa and…

A:

Q: The elongation (mm) in a steel bar having a square cross section is 2.5 mm and subjected to an axial…

A: given- square cross section 2.5 mmaxial tensile load P=250 kNlength L=4 mmodulus of elasticity…

Q: TRY THIS ONE ON YOUR OWN!! Seatwork 1-M Figure: The composite member is shown in the figure. If the…

A:

Q: An aluminum rod 20 mm in diameter and 5 m long is subjected to an axial tensile load of 50 kN…

A:

Q: A tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: Given data in question  Length Diameter  Elongation in length and Diameter  Load To find out…

Q: Value of one of the properties of A36 steel plate within the limit of its elasticity

A: Mechanical Properties Imperial Metric Ultimate Tensile Strength 58,000 – 79,800 psi 400 – 550 MPa…

Q: Determine the elastic section modulus (Sx) and plastic section modulus (Zx) of the following steel…

A: Given The given section is a hollow rectangular section The Breadth of the outer to outer  section B…

Q: A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm x 15.9 mm is…

A: Modulus of elasticity can be defined as the ratio of the stress experienced by a body or in a body…

Q: A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of…

A: Finding out different materials criteria.

Q: If a steel column with cross-sectional area A = 1000 mm2, modulus of elasticity E 200 MPa and length…

A:

Q: A cylindrical rod 360 mm long, having a diameter of 10.0 mm, is to be subjected to a tensile load.…

A: Given Data: The length of a cylindrical rod is, L=360 mm The diameter of a cylindrical rod is,…

Q: A high strength steel with modulus of elasticity of A N/mm, yield strength of B N/mm2 and crushing…

A: We are required to calculate the ductility of steel

Q: A 3003-H14 aluminum alloy rod with 15 mm diameter is subjected to a 9-kNtensile load. Calculate the…

A: Given data: D=15 mm T=9 KN C=9 KN E=70 GPa poisson's ratio=0.33

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

A:

Q: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which…

A: find the maximum weight of the beam that the system can support (in KN).

Q: A force of 100,000 N is applied to an iron bar with a cross-sectional area of 10 mm × 20mm and…

A: The pressure that deforms the material in order to reduce the volume of the material is the…

Q: tensile load of 150 kN is applied to a round metal bar with a diameter of 1 ngth of 80 mm. Under…

A: According to given data A tensile load of 150 kN is applied to a round metal bar with a diameter of…

Q: A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of…

A: