A cylindrical tank has a diameter of 1.4 m. and a total height of 1.8 m. It contains water to a depth 2/3 of its total height. What will be the required angular velocity (in rad/s) such that half of its content will be spilled out? O A. 9.80 rad/s O B. 8.09 rad/s OC. 14.00 rad/s O D. 10.40 rad/s

A cylindrical tank has a diameter of 1.4 m. and a total height of 1.8 m. It contains water to a depth 2/3 of its total height. What will be the required angular velocity (in rad/s) such that half of its content will be spilled out? O A. 9.80 rad/s O B. 8.09 rad/s OC. 14.00 rad/s O D. 10.40 rad/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. A car has an initial speed of 25 m/s and a constant deceleration of 3 m/s^2. Determine the…

A: Using equations:v-u=atv2-u2=2ass=ut+12at2

Q: expression for the veloc as an initial velocity vo.

Q: The elevations of the ski jumping hill are as follows: hA = 44 m hB = 1.6 m hC = 4.9 m If the…

A: Given: hA = 44 mhB = 1.6 mhC = 4.9 m Velocity at point B = 27.9 m/s

Q: The velocity of a particle travelling along the a straight line is v= (3t²-6t)m/ s, where t is in…

Q: 8. On the side of a 1.83 m diameter tank is a 100 mm diameter orifice. If the orifice draws the…

Q: On April 1. a reservoir has a water depth of 8 m. The reservoir is fed by a stream which becomes…

Q: 3. The flywheel rotates with an angular velocity of o = ( 40% ) rad / s, where 0 is in radians.…

Q: The system is released from rest in the configuration shown at time t = 0. Determine the time t when…

A: Given: The mass m1 is 0.8 kg. The mass m2 is 2.9 kg. The static coefficient of friction is 0.29. The…

Q: Ex.5 A water treatment plant is designed to process (100 *10°m/day). The flocculator is (30m long…

A: Flocculator size=30m x 15m x 5m, Treatment plant design capacity=100x103 m3/day, Horizontal shaft…

Q: Water flows out of a hemispherical tank at the constant rate of 18 cu cm per min. If the radius of…

Q: A cylindrical tank has a diameter of 1.4m and a total height of 1.8m. It contains water to a depth…

Q: An electric motor Mis used to reel in cable and hoist a bicycle into the ceiling space of a garage.…

Q: We're watching water flowing over a dam and down a spillway. We see the angle of the spillway is…

A: Given, θ = 18.8o w = 0.0066 km or 6.6 m v = 19.8 m/s

Q: A hydraulic jack contains 2.0 litres of oil as the working fluid. The compressibility of the oil is…

A: Given, Volume of oil(V) = 2ltr=2×10^-3 m^ compressibility (B)= 1.98×10^-10/pa Pressure (p)…

Q: 2. A nozzle inclined at an angle of 55° with the horizontal issues a 45mm diameter water jet at the…

A: V1=15m/s D1=45mm

Q: a cylindrical tank has a diameter of 1.4m. and a total weight of 1.8 m. it contains water to a depth…

Q: Situation #2: Water flows at a rate of 20 L/s from a cylindrical tank through the pipe and nozzle…

A: Given data in question Discharge Diameter To find out Velocities

Q: Water stands in the open-ends U-tube as shown in figure below. If the entire system is rotated about…

A: Weight of liquid of height H=π4×d2×H×ρ×g eq 1

Q: Water enters a 11 horizontal nozzle with a square cross section of 18 by 18 at a speed of 11. The…

Q: A sphere is fired downwards into a medium with an initial speed of 36.59 m/s. If it experiences a…

A: Given data : Initial speed =U U=36.59 m/s Final speed=V V=0 m/s Deceleration=a a=-6×t m/s2 It is…

Q: A projectile is fired vertically with an initial velocity of 257 m/s. Calculate the maximum altitude…

Q: Situation 3 The rocket sled starts from rest and accelerates at a = 30 + 2t m/s2 for the first 10…

Q: Disks A and B each weigh 2 Ib and have initial velocities as shown in the figure. The coefficient of…

Q: 3. A small projectile is fired vertically downward into a fluid medium with an initial velocity of…

Q: What is the rotational speed in rpm of a 0.8 m diameter cylindrical container, held with axis…

A: Given- The given case is shown below in the figure-

Q: 11. An oil of specific gravity 0.8 is flowing through a venturimeter with an inlet diameter of 20 am…

A: Given: Specific gravity of oil, So = 0.8 Inlet diameter, d1 = 20 cm Throat diameter, d2 = 10 cm…

Q: 0.00025 0.0002 0.00015 0.0001 -0.539 0.608 0.00005 0.539 0.608 (y*h)^0.5 • Depending on above…

A: It is required to determine the area of orifice. A=π4D2=π40.0062=2.83×10-5 m2

Q: In performing his favorite workout routine, Jason throws a ball with an initial velocity of 10.8 m/s…

Q: Q20) For the steady flow of gas in the conduit shown, what is the mean velocity at section 2? Answer…

Q: An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a…

A: Given- a1= 0.40 m²a2=0.0003 m²t=312sh1=1.20mh2=0.60m

Q: A ride in an amusement park consists of a rotating arm AB having a constant angular velocity wAB =3…

Q: A cylindrical tank has a diameter of 1.4 m. and a total height of 1.8 m. It contains water to a…

Q: A Sharp-edged orifice 10 cm in diameter, in the side of a tank having cross section 2 m square,…

A: Cd=0.67 d=10cm

Q: The water in an aquarium will be drained for cleaning. A flexible tube (D = 4mm) will be used to…

Q: Two smooth disks A and B each have a mass of 0.5 kg. If both disks are moving with the velocities…

Q: An orifice with an area of 25 cm2 in a vertical plate has a head of 1.13m of oil with sp.gr 0.89. It…

Q: An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a…

A: given data: An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The…

Q: Oil is flowing upward through a Venturi meter as shown. Assuming discharge coefficient of 0.984,…

Q: A sharp-edged orifice 10 cm in diameter, in the side of a tank having cross section 2 m square,…

A: Given Orifice dia= 10 cm Square side = 2 m Discharge changes from 0.023 to 0.034 m3/s C= 0.67

Q: PROBLEM 8 Oil of absolute viscosity 0.00210 Ib-s/ft? and specific gravity 0.850 flows through 10,000…

Q: The tank in Fig. (4) has a 4-cm diameter plug which will pop out if the hydrostatic force on t…

A: Given Diameter,D=0.04m Temperature T=20℃ Hydrostatic force F=25N Density of water =1000kg/m^3…

Q: 7.12 The globe valve in the pipeline shown is opened instantaneously. If the loss coefficient for…

A: Given, Loss coefficient for the wide-open valve, K= 3.0 Length of the pipe, L= 2000'12" f= 0.018…

Q: he 233000-lb space-shuttle orbiter touches down at about 237 mi/hr. At 208 mi/hr its drag parachute…

Q: 3. A closed cylindrical tank, 6 feet in diameter and 12 feet high contains water to a depth of 10…

A: Rotating a closed vertical cylindrical vessel about its central axis is a condition of forced vortex…

Q: 6. What is the velocity of water under a 50 ft head dis- charging through a 1 in diameter…

A: Given figure: 50 ft head discharge, h = 50 ft g = 32.2 standard value

Q: H.W.: A horizontal venturimeter with diameter 20cm and throat 10 cm is used to measure the flow of…

A: To find the reading of the oil- mercury differential manometer-

Q: A sphere is fired downwards into a medium with an initial speed of 27.76 m/s. If it experiences a…

Q: 9. A missile is rising at a constant rate of 100 meters per second. An observer is 600 meters away…

A: Given values: Missile rising speed, V= 100 m/s Distance of observer from launching pad, X = 600 m…

Q: A hemisphere of radus 12 nches and base up is full of water that runs out through an orifice of area…

A: Given data, Radius of hemisphere = 12 inch Area of orifice = 1 in² Orifice coefficient = 1.0…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

A cylindrical tank has a diameter of 1.4 m. and a total height of 1.8 m. It contains water to a depth 2/3 of its total height. What will be the required angular velocity (in rad/s) such that half of its content will be spilled out?
O A. 9.80 rad/s
O B. 8.09 rad/s
O. 14.00 rad/s
O D. 10.40 rad/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

a cylindrical tank has a diameter of 1.4m. and a total weight of 1.8 m. it contains water to a depth 2/3 of its total height. what will be the required angular velocity (in rad/s) such that half of its content will be spilled out? a) 9,80 rad/s b) 14.00 rad/s c) 10.40 rad/s d) 8.09 rad/s
A cylindrical tank has a diameter of 1.4m and a total height of 1.8m. It contains water to a depth 2/3 of its total height. What will be the required angular velocity in rad/s such that half of its content spilled out? A. 14.00 rad/s B. 8.09 rad/s C. 10.40 rad/s D. 9.80 rad/s
An elevated water tank consists of an upper cylindrical part (4.88 m in diamwter and 6.10 m high) and a lower hemispherical part, at the lowest point of which is an orifice 310 mm in diameter (C=0.60). If, at time t=0, the tank is full of water, when will the water level drop down 6.71m, after opening the orifice? 35 seconds 415 seconds 235 seconds 260 seconds
The 233000-lb space-shuttle orbiter touches down at about 237 mi/hr. At 208 mi/hr its drag parachute deploys. At 45 mi/hr, the chute is jettisoned from the orbiter. If the deceleration in feet per second squared during the time that the chute is deployed is -0.000170v2 (speed v in feet per second), determine the corresponding distance s traveled by the orbiter. Assume no braking from its wheel brakes.
A closed cylindrical tank 1.845m high and 0.945m in diameter contains water of height 1.35m. When the angular velocity is constant at 20rad/sec , If it is rotated at 15rad/sec and the air has a pressure of 200kPa what is the minimum pressure at the bottom of the tank in KPa? CHOICES a.) 220.48 b.) 22.48 c.) 202.48 d.) 248.22
A jet of water discharges into a 90-cm open cylindrical tank with a height of 1 m. The cross-sectionalarea of the jet is 0.0025 m2 where the velocity of water jet is 3 m/s. How many seconds is requiredto fully fill the tank? The following are given for the measurements of a 90-cm open cylindrical tank when a jet of water discharges. height= 1m velocity=3m/s Area=0.0025m2 Determine the time to fully fill the cylindrical tank.
Open cylindrical tank 1 m in diameter and 2.5 m high is three-fifth full of water. If the tank is rotated about its vertical axis, which of the following gives the angular velocity in rpm so the depth of water at the center is zero?
4. An open cylindrical tank 2 m in diameter and 4 m high contains water to a depth of 3 m. It is rotated about its own vertical axis with a constant angular speed. a. If w = 8 rad/s, how much water is spilled out and to what depth will the water stand when brought to rest?b.What angular speed w (in rpm) will just zero the depth of water at the center or the tank?c.If w = 100 rpm, how much area at the bottom of the tank is uncovered?
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the time in seconds to lower the head from 1.20 m to 0.80 m?
The open-top cylinder vessel, 0.5 m in diameter and 1.0 m in height, is filled with a liquid up to 0.75 in height. Calculate the constant angular velocity and at what constant speed the cylinder should be rotated around the vertical axis of the container so that the paraboloid of the free surface of the liquid is tangent to the bottom of the container. Then find the volume of fluid ejected from the cylinder container in this case.
In a rectangular channel 12 m wide and 3.6 m deep water is flowing with a velocity of 1.2 m/s. The bed slope of the channel is 1 in 4000. If the flow of water through the channel is regulated in such a way that the energy line is having a slope of 0.00004 to find the rate of change of the depth of water in the channel.
An open cylindrical tank having a radius of 0.34 m. Is filled with water at a depth of 0.84 m. If it is rotated about its vertical axis to a velocity of 110 rpm, what should be the height in meters so that no water will be spilled out